Jump to content
SAU Community

Recommended Posts

Parts for Sale

Located In Ballarat VIC

Will post most parts at Buyers expense

Open to offers

****RB30 Parts****

R31 Auto Gearbox Computer (Located under passenger seat)
-A64-000 J29 $5
-A64-000 J41 x2 $5

Charcoal Canister $20
Power steering Res $20
O2 Sensor x2 $20 each
Idle Air adjust with FICD $20
Pressure Reg – Solenoid Valve $20
Auto Throttle Position Sensor $5
Air Reg x2 $10 each
Factory Water inlet and out block fittings (Rad hoses connect to) $5 each
CAS(Crank Angle Sensor) x2 $10 each
Coils x4 $10 each
Pressure Reg $10
Throttle body x2 1Missing the Throttle cable connector $10 each
Dizzy x2 $20 Each
Throttle cable holder Block bracket $5
Starter Motor x2 $25 each
Alternator $25
Fuel Pump out of Cradle $20

****Outside Parts****

Chrome Door Handles – All Except Drivers Side $40
Black Door Handle – Front Passenger side $10
Bonnet Hinges Both Left and right $5 each
Fuel Cap $5
S3 Headlight Drivers Side $25
S3 Headlight Passenger side x3 $25 each
Front Bar Indicators – Both sides $10
Chrome Strips that go above the top of the doors – both sides $30
Side Indicators – Both sides $10
Wagon Drivers Side Tail light $10
Wagon Passenger Side Tail light – Small Crack $5
S3 Filler bar x2 $10 each
S2 Filler Bar $10
S2 Passenger Gaurd $20
S3 Passenger and Drivers Side Gaurds $20 each
S3 Front Bar $50
S3 Rear Bar $50
Stock sway bar $10

****Interior Parts****

Ash tray - $5
6 Gauge Cluster x2 $30 each
Pintara cluster (Clock where the rev gauge is) $10
Random Brown interior – Too much to list – Let me know what you after
Random grey dash buttons - Let me know what you after
Grey dash - $20
Brown Dash insert S3 TI (The whole thing the dash sits in) $50
Indicator/Headlight stork x3 $20 each
Wiper stork 1x Adjuster $20 x1 Non Adjuster $10

Link to comment
https://www.sau.com.au/forums/topic/456919-vic-r31-skyline-rb30-parts/
Share on other sites

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kaizo Industries put a VIN plate over where the Nissan plate would go. It was part of how they broke the law and attracted feds going after them.
    • Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
×
×
  • Create New...