Jump to content
SAU Community

Replaced Speedo Now The Power Steering Is Heavy ?

adam wicks

By adam wicks,
in General Maintenance

 Share

Recommended Posts

adam wicks Collaborator

adam wicks

Posted
Posted

I recently replaced my speedo cause the other broke in my Nissan skyline r32 gtst 1993. The new speedo all works, when the car is started the power steering works fine but after a little drive for about 30 seconds if that the steering goes heavy?

I've had a read about some sensor but I have no idea where it is and what to do about it ?

Any help would be great thanks

Hadouken Grand Master

Hadouken

Posted
Posted

Have you back tracked? Ie

Take the cluster back out and check all connections. Apparently the sensor is at the back of the dash and the steering angle sensor is in the column.

Put the old cluster back in and see if you have power steering back.

Process of elimination.

Check your power steer reservoir.

ErOR Contributor

ErOR

Posted
Posted

The sensor behind the dash is the one coming from the gearbox. It's a big round hole with a small shaft sticking out of it right behind the gauge cluster. That's where the speego gets its reading from. Funny that your speedo works but you get heavy steering as usually when that pin breaks and car no longer receives a speed signal is when you get the heavy steering.

You might have to do a HICAS diagnostic test and see what comes up.

ErOR Contributor

ErOR

Posted
Posted (edited)

Have you had a look at the fuses?

All I could point my finger at this point is some kind of a bad connection...

Since you're using a lock bar like me, do you have anything unplugged from hicas ecu? Silver box under the parcel tray.

To get into HICAS diags:
1) Switch ingition off, transmission in neutral or auto in Park.
2) Start engine
3) Very quickly (with a couple of seconds), turn the steering wheel left and right about 20 degrees from centre five times, and then pump the brakes five times, then press the brake pedal once more - this will enter diagnostic mode.
4) Drive forwards or backwards about 5 metres at a speed less than 10k/ph, this will enter full diagnostic mode.
5) The HICAS light in the instrument cluster will be flashing quickly (for normal) or will flash a code indicating any problems. Long flash = first digit, short flash = second digit. Diagnostics will return to normal after five minutes, or any speed over 10k/ph, or ingnition is turned off.

Result codes:
11 HICAS control unit
12 HICAS motor power supply not present
13 HICAS motor output not present
21 Vehicle speed sensor not present
22 Steering angle sensor not present
23 Steering angle sensor neutral or not present
24 Rear main sensor input not present
25 Rear sub sensor input not present
31 Parking brake sensor input not present
32 (Auto) Inhibititor switch input not present
(Manual) Neutral switch input not present
33 Engine speed signal not present
Edited by ErOR
adam wicks Collaborator

adam wicks

Posted
  • Author
Posted

The lock bar was installed by the last owner so I'm not sure but I've owned the car for about a year and never had a problem till I replaced the cluster, I'll do the diagnostics and see what happens, I did an ecu diagnostics and it was all okay

jiffo Mentor

jiffo

Posted
Posted

What sensor are you testing?

The item on the column behind the steering wheel is the steering angle sensor and since you've deleted HICAS I can's see it having any input.

You swapped the dash and then your troubles began so to me it's a speed sensor problem.

The actual speed sensor is just a reed switch built into the speedo right where the cable enters.

There's differences between early/late models, so could be a wiring issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By soviet_merlin · Posted

      Holy shit, I'm glad you brought up the battery issue and I'm glad I asked about measuring it. Old battery was at a healthy 12.82V in the morning with the car turned off. Removed the fuel pump fuse, clamped the multimeter on at min/max/average and cranked for ~3 seconds. It dropped down to 8.30V. So yeah, not surprising it struggled that much. Picked up a fresh battery from supercheap and it's ridiculous. Haven't done a cold start yet, but man, even with a warm start the difference is night and day. I can't believe I lived with this for so long. Just blamed it on it being an old modified car. Went with Century because convenient. If they are shit it'll be a future me problem. But just in case I set up a reminder for 30 months - 8 weeks to check on the battery state and get a warranty replacement if necessary. 
    • Dose Pipe Sutututu
      R34 GTT AC short cycling ? Normal behaviour?

      By Dose Pipe Sutututu · Posted

      This is the thread:    
    • Dose Pipe Sutututu
      R34 GTT AC short cycling ? Normal behaviour?

      By Dose Pipe Sutututu · Posted

      There's another sensor that sits inside the evaporator, that's a C U N T to get to, but can be done without removing the entire unit. Usually it's not the sensor that dies but the actual capacitor in the circuit (part of the plug that dies).  
    • GTSBoy
      R34 GTT AC short cycling ? Normal behaviour?

      By GTSBoy · Posted

      Putting the climate control CU into diagnostic mode is independent of the ECU. You just have to do the dance prescribed in the manual. No, I do not know what the dance is. I have an R32, so use the dance in the R32 manual. On older cars, I would have said "no, the ECU should not affect whether the A/C works".... but for an R34 that might be wrong. I don't recall the detail, but there was extra mods required to make my R32 A/C work against the R34 ECU. The R34 ECU apparently gets involved in the running of the A/C more than earlier cars did. Theoretically, if the PFC is a true plug in, then it should just work the way that the original ECU does - wrt A/C. But there's always scope for them to have not cared. Nope. Pressure switch out = getting the fridgey out to pump the gas out before pulling the switch. The switch really cannot sense gas pressure unless it is up against the gas.
    • George.
      R34 GTT AC short cycling ? Normal behaviour?

      By George. · Posted

      Hi guys, thanks for the replies.  I will have to wait till summer to test properly, but it short cycles both when heating and cooling. I’ve ordered a new internal temp sensor that sits under the vent in the steering wheel also, GTSBOY, I have an Apexi FC ecu, I’m assuming I won’t be able to diagnose or would it still work? Could the ecu be causing the problem??   the pressure switch is quite cheap I will get a new one and try it out, hopefully it doesn’t require purging the refrigerant again?
×
×
  • Create New...