Jump to content
SAU Community

Steering Wheel Series 1 To Series 2 Nissan Skyline R33

Rado33

By Rado33,
in General Maintenance

 Share

Recommended Posts

Rado33 Rookie

Rado33

Posted
Posted

Hey guys I got a Series 2 steering wheel fitted into my R33 and I was wondering is there anyway possible I could make the horn work? I've got a Series 2 motor with a Series 1 body. If anyone can help me would be much appreciated. Also I like to mention that I changed the Relay and 10 Red fuse and still no luck. If anyone is out there to help me I'd be more then thankful for your help. If someone could possibly help me out that has been through a similar situation and meets my requirements would be thankful for the help.

I'm open to any opinion but don't quote anything stupid because I won't tolerate any rude behaviour.

  • Like 1
89CAL Grand Master

89CAL

Posted
Posted

Your horn doesnt work after youve changed steering wheels? Sounds like something wasnt plugged in properly when the wheel was put on. The s2 wheels have air bags (all of them AFAIK, maybe the GTS' dont?) So are you sure you havent hooked something up wrong?

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

S1 (with airbag) vs S2 with airbag is very different.

S1 has the SRS module built into the wheel where as most (not all) S2 has the SRS module under the centre console.

If you want a S2 wheel, perhaps get a 180SX Type-X wheel as it uses the same setup as the older S1 with airbag.

  • 1 month later...
Rado33 Rookie

Rado33

Posted
  • Author
Posted

Should only be a ground wire. I've done s2 stag to a s1. So tech it's 34 to 33.

Hey bro how did you get that to work? Because my mate gave me his Steering wheel out of his 180sx and I put it in mine and theres still no luck to get it to work. If u can help it would be much appreciated.

Rado33 Rookie

Rado33

Posted
  • Author
Posted
S1 (with airbag) vs S2 with airbag is very different.

S1 has the SRS module built into the wheel where as most (not all) S2 has the SRS module under the centre console.

If you want a S2 wheel, perhaps get a 180SX Type-X wheel as it uses the same setup as the older S1 with airbag.[/quote

I've got one steering wheel from my mates 180sx but theres still no luck getting the horn to work

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Possible swap on R34 RB20DE NEO?

      By GTSBoy · Posted

      If the RB29 box in the car is a push clutch, then yes, you will need to deal with the pull clutch on the turbo box. You either buy a pull clutch and don't use the old one, or you do the things needed to convert the turbo box's clutch arrangement over to push. Which is a bit of a f**karound. "Making" a custom tailshaft is the easy part. But you will need to source the front clip yoke - the bit that goes into the output of the gearbox. These are not as easy to find. They are out there, but they don't grow on trees the way that they used to.
    • GTSBoy
      Turn signal wiring question

      By GTSBoy · Posted

      Indicator bulbs are way too bright to use as a "corner marker" (we call them parking lights too). Sure. Go ahead and do it. But realise that you wil need to come up with all your own wiring to do it, as no-one will have a standard howto worked out for Skylines. It's just a matter of abandoning everything that Nissan have done and starting from scratch. You'd probably be better off retrofitting tailght/brakelight globe bases into the front indicator housings and using the taillight circuit for your corner marker and the brake light as the indicator. You'd need to work out how to kill the marker circuit while the indicator is flashing, otherwise it won't flash on-off, just bright-less bright.
    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
×
×
  • Create New...