Jump to content
SAU Community

Recommended Posts

these are the parts that i have left no reasonable offer denied

rear bar grey in colour bit faded $40

reinforcement behind rear bar $15

front seats out of m spec immac $300

rear seats out of m spec $90

grey carpet $40

grey hoodlining $30

fuel tank with fuel pump and sender $50

rear window $100

left hand quarter window with rubber $50

rear sub frame with hubs & control arms SOLD

gts4 or gtr front hubs control arms and struts $80

ac compressor $40

manual tail shaft $40

all plastics from center console and radio facia

brake master cyl with pipes and abs unit $100

A PILLAR TRIMS $25 EACH

LH POWER MIRROR $40

complete top end rb20det head, manifolds, turbo wiring, computer asking $400

no gearbox

no coils or ignitor

no dash or vents

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/
Share on other sites

is the boot charcoal metalic or gray as described???

Also do you have the metal lining that goes around the rear windo its a three piece metal strip thing???? PM me your mobile and i can have a chat about some stuff and prices!!!

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-931254
Share on other sites

Need 2 x o2 sensors out of GTR r32 , the ones that scew into dumps , must be working please.

these are the parts that i have left no reasonable offer denied

boot lid imac with wing off m spec gray in colour $90

rear bar grey in colour bit faded $30

rear seats out of m spec $90

both doors with all internals and glass . no door trims $200

grey carpet $40

grey hoodlining $30

fuel tank with fuel pump and sender $50

rear window $100

rear sub frame with hubs & control arms $80

gts4 or gtr front hubs control arms and struts $80

ac compressor $40

manual tail shaft $40

complete top end rb20det head, manifolds, turbo wiring, computer asking $400

no gearbox

no coils or ignitor

no dash or vents

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-931497
Share on other sites

these are the parts that i have left no reasonable offer denied

no gearbox

no coils or ignitor

no dash or vents

What about the underbody plastic bit RHF Guard - protects the BOV are from road dirt?

Odd screws/connectors from the bumper etc?

R32 GTR not sure if other cars are different

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-934827
Share on other sites

Hey man if you know if the R32 drivers side window is the same as an R33 and in good condition send pic if possible i'll take it plus its internals $130 and i'll front the shipping.

PM me. thanks

i'd say it would be different

Link to comment
https://www.sau.com.au/forums/topic/45748-wrecking-r32/#findComment-939147
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...