Jump to content
SAU Community

Recommended Posts

No worries. I'm running a 25/30 neo as well so done it all before :)

Hey just a quicky - Did you bother adding material to either the head or block to get a better seal on the headgasket around water galleries?

I was overlaying the 2 and there is clearly a mismatch but still some landing that would probably make a seal. I was thinking about just using a little RTV around that area since the rubbery rings in the headgasket in that area won't engage on the head.

I can fairly easily add material to the head and dress it back but if you've got first hand experience of not doing it I could be talked out of the work.

Dave

I might be wrong but when i was comparing headgaskets ( RB30,25 and 26)there was one that seemed thin around a water gallery, i'm going RB26 headgasket, it looked the best fit everywhere.. :glare:

Your right, they are all thin around the front gallery :glare: , probably 2mm which isnt brilliant, someone should add all these fine details into the Guide.. just got the head back from the shop too :down:

http://stevenwelsh.site.net.au/RB30_DOHC.pdf

I didnt see anything about welding beads on the gallery, should make a new guide thats more detailed... :yes: old man reckons weld more material so im gonna do that, i know that people get away with it ( i usually dont have that luck and have to do shit twice) but i dont like taking chances, 2mm contact area sounds bit dodgey.. what did you do here Ben? bolt it down or weld extra material??

Edited by AngryRB

So after reading this I thought bugger it ill just Weld it up. Decided while I had the tig out I'd just Weld up the oil feed as well since there is zero chance of it ever going back on an rb25 block. I attached some average pics for anyone who may be interested. The old water gallery is a typically contaminated surface so be sure to run plenty of AC balance.

post-41244-0-96359600-1443525867_thumb.jpg

post-41244-0-92991400-1443525940_thumb.jpg

post-41244-0-66241100-1443526009_thumb.jpg

Edited by dave1200
  • Like 1

Yeah I knocked one up a couple of weeks ago. I'm going to run this hose to the 3/4" BSP fitting in the block since I'm going N/A. Then Vent this tube also up to the catch can (in the bottom also acting like a drain for catch can). I'll plumb the 2 rocker covers to the catch can also then run the catch can breather to the inlet to keep it legal.

post-41244-0-82481500-1443571850_thumb.jpg

  • Like 1
  • 5 months later...
  • 5 months later...

Hey guys a bit of an update.

I lost a battle with the committee and had to sell my R31. I did however decide to keep building this motor. I found a healthy R31 Rb30 and as of tonight just got the Rb25 head torqued down. I set up all the timing gear and turned up some oil restrictors before cleaning the block and giving it a coat of paint. Here's a couple of pics for anyone who's interested. I've actually set up my gopro to take time lapse photos of the build for shits and giggles which I'll whack up one day if anybody would be interested. A keen eye will spot I have used a block without the machine face where the idler pulley sits. I've made up a 5mm plate to bridge it and machine that amount off the idler to suit. Not ideal but hey we're building a budget setup.

 

Has anybody else noticed when you use the concentric idler in the drive side of the timing gear that you timing marks don't line up perfectly? I have trialed a second tensioner in that place and can dial in the timing marks HOWEVER this makes me nervous in the case that it slips and throws the cam timing out. Thoughts?

 

20160819_222321.jpg

20160819_222342.jpg

20160825_212148.jpg

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It might be fine. I was just saying that I wouldn't trust it without testing it.
    • Traction wasn't bad, l couldn't give it everything off the line but was able to go WOT about half a second after rolling - good for NZ drag strips.   Like one run I did a 1.96 60ft and pretty sure I was on for a 12.4 but lifted early as I was on a 12.5 dial in, and still won haha 
    • Nice one! I was going to take mine down to SMSP drags one Weds night. I'd love to compare it with my GTR which did a 12.3. The bum-dyno in the 335i says its quicker.   How was the traction @Lithium?
    • AFAIK I've seen other people recommend using the back of the balance tube as well. Andre Simon from HPA at least. I can't imagine it being that far off from ideal even if it was only used to drive a boost gauge from the factory.
    • Hi All, New member here, I've joined to help my son with an issue that is truly doing our heads in. I'll start with a bit of an overview. Chris carried out some modifications to the engine to try and extract just a little extra power out of the motor and make it a bit more efficient. Previous to this work, the car already had an upgraded exhaust, increased boost up to 14psi, modified standard turbo to metal impellers and slightly oversized, upgraded fuel pump, been dyno-tuned at JEM, and some other bits n bobs like coil packs etc. Before the current mods it was making 236rwkw at 14psi but after the new mods it now makes 209rwkw at 14psi. The work he carried out is as follows, timing belt service, water pump replacement, return to sump radium catch can, had oem head rebuilt and machined 0.2mm, fitted Athena cut ring head gasket 1.2mm thick, arp 2000 head studs, added rear prp head drain, added an external wastegate 40mm turbosmart welded off the stock manifold and plumbed back into a 3in dump. The car has been on the dyno and apparently the ignition is working, fuel flow and fuel pressure is fine, injectors are fine, spark plugs are working fine, Maf is working, O2 sensor is working, TPs sensor is working, VCT is working, CAS is working, boost leak test showed no boost leaks, compression test first crank cold 135psi and got to 150psi across all cylinders once cranking, timing is confirmed at tdc with a dial gauge and the cam dots line up, no blockages in intercoolerm throttle body or pre-turbo intake, no blockages in exhaust, cat conveter or down pipe, turbo looks fine and spins and wastegate looks fine and is new. Soz for all the detail but after all this, it has been in 3 times for dyno and each time comes back stating it's not going to make power. After the first (or second, can't remember now) trip to dyno we did find the timing out by one tooth and this improved things, but it is still well down. Does anyone have any ideas?  Any replies much appreciated as we're just not sure of which direction to take this. Regards Rob (Chris's Dad).
×
×
  • Create New...