Jump to content
SAU Community

Recommended Posts

Hi guys,

a couple of days ago after a hard drive back from the airport my R32 started idling funny. When warm it started bouncing from idle (800 rpm) to 2000 rpm. I've been driving the car for a couple of days now, and it's quite embarassing. When I'm at the lights people think I'm trying to run them!

I have searched the forums long and hard, and have cleaned my AAC Valve to no avail. I now believe it is the air regulator. Problem is I don't know were this is. I read that it was underneath the intake plenum. If someone could take a pic that would be great. Also if anyone knows if this part is servicable, or will I need to replace it?

If anyone esle has had the same problem I would love to hear their input.

Link to comment
https://www.sau.com.au/forums/topic/45774-r32-gts-t-fluctuating-idle/
Share on other sites

I've had a really bad fluctuating idle that also had a slight miss.

I cleaned the AAC valve and the idle fluctuation was ALMOST gone.

2 years later I put the mesh back on to the AFM and all idle problems are gone.

Its now got a 100% perfect smooth idle.

I have heard of o2 sensors also causing an issue.

My actions would be.

Clean AAC valve

Check if your afm has mesh on both the front and rear. If not slap it on.

If idle problems are still around either get your injectors cleaned/checked out or replace the o2 sensor.

after a really hard run, e.g. running 70 laps on a circuit over a whole trackday, the hydraulic lifters sometimes get a bit stuffed, which would also cause the funny idle. will usually go back to normal after a few days, or after a service. my own experience.. :D

after a really hard run, e.g. running 70 laps on a circuit over a whole trackday, the hydraulic lifters sometimes get a bit stuffed, which would also cause the funny idle.  will usually go back to normal after a few days, or after a service.  my own experience.. :D

70 laps would see the complete breakdown of your engine oil, almost to a water like state, hence the problem with the lifters. Do you have a oil cooler? What sort of oil do you run?

In regards to idle problem, AAC valve is usually the culprit

Ok guys,

Nissan called this mourning and after 2 days of tying to figure it out there still unsure. They said that because it's an import there diagnostic machine can't read

all the codes?! Thay reffered me to another workshop. On top of this they tried to

charge me for there time. I refused to pay as I don't think they did anything.

Hopefully I have better luck with the next place.

chris32 - heheh i don't run 70 laps all in one go... 10-15 laps at a time, 5-7 sessions a trackday. Using Valvoline fully syn, car has run extremely reliably for over a year of about 15 trackdays inc 2 at Eastern Creek with very low knock readings (std 11 yr old engine with HKS 2530). Running a BEL Garage 19 row oil cooler and 3-core radiator.

chris32 - heheh i don't run 70 laps all in one go... 10-15 laps at a time, 5-7 sessions a trackday.  Using Valvoline fully syn, car has run extremely reliably for over a year of about 15 trackdays inc 2 at Eastern Creek with very low knock readings (std 11 yr old engine with HKS 2530).  Running a BEL Garage 19 row oil cooler and 3-core radiator.

cool, sounds like a good setup you have there. I run a decent oil cooler myself, and a similar turbo to yours. Only have done one trackday of about 25 laps, but it kept it nice and cool

Chris

why keep on guessing by replacing this and replacing that???? You need to systimatically go through all the vacuum piping to and from the AAC valve & idle control solenoid and clamp them off with a brake line clamp and see if this changes the fast idle. Simple. If the idle does not change then its something else like a inlet manifold gasket blown out (very common in older skylines).

This can be confirmed with the ol can of break disc cleaner in an aerosol can. Give it a squirt alone the inlet manifold right against the cylinder head and if the gasket is gone, broken, blown out, it will get sucked in and the idle will stumble as it burns the break cleaner fluid.

Give that a go.

Changing the O2 sensor just for the sake of it could well be a waste of your money, besides, even if it is stuffed that won't make your idle jump up & down like that.

MIke

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not noticeably. Arguably, the catless turbo is going to work harder in a different direction, as it will spool up faster, go to higher speeds more easily. Only if it was tuned in the original condition. If it was a stock tune, using the AFM before and after the cat/dump change, then no, no retune needed. If the car is running on a MAP sensor, then it might well benefit from a retune. It might even run a little dangerously without a retune, but it could quite easily be fine.
    • We had this blend that uses 98RON + 10% Ethanol which brought it to 100RON. It's no longer available anymore unfortunately.
    • Does it make a difference in your turbo having a shorter life if you have a cat converter as it causes that back pressure versus less/no back pressure with a decat? (Not sure if this is accurate) Also slightly different question if you went from a oem cat to a decat or vice versa will it require a tune? I heard if you change the dump pipe onwards it requires a tune?
    • No. Have only gotten as far as contemplating the task of having to put in the required fairly heavy wiring and fusing to run it (along with the big alternator), and preferring not to. But otherwise, it would be nice to have a little extra freedom as to exactly where the compressor is located and free up some space around the exhaust side of the engine.
    • Following from this in a related by not closely-related sense... Because I was buying a bunch of other GKTech stuff, I got some rear subframe collars. The history that leads up to this is: 25+ years ago the car arrived into the country with stock subframe bushes. At some point shortly thereafter I added Whiteline pineapple rings, set up neutral, and it improved the rear end behaviour. Well, it is my vague memory that I was happier with it with them in. Less axle tramp on launches, generally better, etc etc. ~2012 it got a new non-HICAS subframe with new stock bushes. No pineapple rings. I reckon that ever since then I've been dissatisfied with the axle tramp. Recently I've been f**king around a lot with all aspects of the suspension. One contemplation has been to relocate the rear lower control arm front mount points (and do the other things needed to make that work) to improve longitudinal rear grip by getting rid of some of the stupid anti-squat that Nissan ladled into the R32. But.... before doing that I thought I'd put some collars in. And.... The collars are good. The rear sounds a little bit different, but there has been no significant increase in NVH coming up into the body. In terms of rear behaviour - expansion joints on long sweeping elevated freeway ramps that would sometimes cause the rear to jiggle around a bit, no longer seem to do so. It appears that jamming chunks of metal into the gaps in the rubber so they can't move much is a really good thing. And the launch behaviour and general forward traction situation seems to be greatly improved too. It's impossible to be really sure, because the tyres are completely shagged - they are freakishly willing to let go right now. But as an A-B test with the same tyres it certainly seems to grip up a lot better. Highly recommended to anyone who still has stock bushes.
×
×
  • Create New...