Jump to content
SAU Community

Recommended Posts

hey there peeps, i am stumped at finding where this problem is, i get this small shaking in the steering wheel at about 100km/h but the thing is sometimes goes away i think when taking a slight bend but not 100% sure

the thing i have done so far is, balanced front wheels, i have check for any play on the front end, all good there and i also have put in hub centric rings too

i have notice a bit of play in my rear end seem the tie rod ends at the rear are shot but will i wouldnt think that would cause the steering shake at the front or would it?

Have been in a car where a rear wheel buckle caused the steering to shake.

Get all wheels balanced. And what tyres are you running? Have also had shit tyres that caused the steering to shake no matter who balanced them

Im running federals 595 up front and duruns at rear. I have had this problem with 2 of my other sets of wheels. But i will try get the rears balanced and see if that makes an improvement. Also when i get time prob install my emliminator kit as im running a lock bar right now but tie rod ball joint is shot

  • 4 months later...

I had a similar problem that I lived with for years... Felt like a front wheel imbalance, but would come and go at different times.

I finally fixed it when I swapped out the stock inner bushes (with Nolathane items) on the front lower control arms.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...