Jump to content
SAU Community

Recommended Posts

On 03/07/2021 at 9:59 AM, Dose Pipe Sutututu said:

Needs twins to be a GT-R, or be like Advan and put twins in a GTS-4, and put GT-R guards on it. GT-R with sunroof lol.

He argued that till he was blue in the face and went quiet after I hit him with “does the Japanese vin start with bcnr33?” 

  • Like 1
  • Haha 1
On 04/07/2021 at 8:37 AM, WantGTR said:

This is genius 

Then all the GT-R boys can do single turbo conversions and pop in NEO blocks to be GTS-4s.

@r32-25t you going to redo the engine loom too? I'm tempted at the moment as well. I stripped back the OEM loom and it's still good so kind of feels like a waste.

On 04/07/2021 at 9:35 AM, Dose Pipe Sutututu said:

Then all the GT-R boys can do single turbo conversions and pop in NEO blocks to be GTS-4s.

@r32-25t you going to redo the engine loom too? I'm tempted at the moment as well. I stripped back the OEM loom and it's still good so kind of feels like a waste.

Yeah I will be replacing the engine harness, just look at it being almost 30yrs old and it’s out at the moment so may as well 

  • Like 1
On 7/4/2021 at 2:29 PM, r32-25t said:

Injector have been changed twice and turbos 3 times 

at least I’m not the mack daddy of the 80k rust bucket 

850s

1000s

1250s

Then 1650s

come on Brett… I thought you did the maths, & do it once and do it right?

I’ll stick with my Mack daddy “rust bucket” thanks, at least it has a blue plate 😂😂😂

I’ve never had 850s 

building cars is a journey and one I’m happy I took because I enjoy working on my car not writing cheques for other people to do it. 
 

so unless you actually have anything useful to say I’d appreciate if you troll other parts of the forum, like I give you to the courtesy of staying out of your threads 

On 04/07/2021 at 9:39 AM, r32-25t said:

Yeah I will be replacing the engine harness, just look at it being almost 30yrs old and it’s out at the moment so may as well 

Going a new OEM one or custom and deleting the crap you don't need like the AFM wiring?

AFM wiring actually turns out to be perfect for wiring in an EMAP sensor.

On 04/07/2021 at 8:46 PM, Dose Pipe Sutututu said:

Going a new OEM one or custom and deleting the crap you don't need like the AFM wiring?

AFM wiring actually turns out to be perfect for wiring in an EMAP sensor.

Going to grab the wiring specialties one and remove the wires I don’t require and replace them with ones that I do need ie. Load cell and pressure sensors a

  • Like 1

Because of needing the bay to go back to bare metal the shop tried to use stripper to remove the paint and because it wouldn’t remove the undercoat it was decided blasting is the only option.

89A87F5E-245E-4A47-9184-B2B054EF878C.thumb.jpeg.17990aaa9e57ba8a4ca7c2b3db2616f0.jpegD4718691-79C7-4EB0-BC73-FF66D42C3E67.thumb.jpeg.95bd040ae457070734d57f46c0f43e39.jpeg Because of that he wanted the cross member removed and while I was there I removed a the rest of the lines and grabbed plugs for all the AN lines 

blasting is booked and so is the tow truck 

  • Like 2
On 10/07/2021 at 1:51 PM, r32-25t said:

Because of needing the bay to go back to bare metal the shop tried to use stripper to remove the paint and because it wouldn’t remove the undercoat it was decided blasting is the only option.

89A87F5E-245E-4A47-9184-B2B054EF878C.thumb.jpeg.17990aaa9e57ba8a4ca7c2b3db2616f0.jpegD4718691-79C7-4EB0-BC73-FF66D42C3E67.thumb.jpeg.95bd040ae457070734d57f46c0f43e39.jpeg Because of that he wanted the cross member removed and while I was there I removed a the rest of the lines and grabbed plugs for all the AN lines 

blasting is booked and so is the tow truck 

Somehow, it finds a way to escalate 🤪

  • Haha 1
On 11/07/2021 at 7:49 PM, r32-25t said:

There’s always these little things you never expect but I’d rather just do it and end up with a perfect job 

Yep, I said the same, and now 5k in parts later 🤔

The parts I’d really like to buy is the brake lines, Nismo heritage have some of them but according to their pictures they don’t have the complete abs versions. 
 

they have the lines that go from the master to the pump but don’t have the ones that go from the pump to the left and right fronts or the one that goes from the pump to the rear. And nissan in their wisdom made both abs and non abs lines the same part numbers despite them being completely different shapes and sizes 

On 12/07/2021 at 7:54 PM, r32-25t said:

The parts I’d really like to buy is the brake lines, Nismo heritage have some of them but according to their pictures they don’t have the complete abs versions. 
 

they have the lines that go from the master to the pump but don’t have the ones that go from the pump to the left and right fronts or the one that goes from the pump to the rear. And nissan in their wisdom made both abs and non abs lines the same part numbers despite them being completely different shapes and sizes 

No, all the brake lines are available from Nismo for front and rear and the abs and non abs pipes are not the same part numbers. We replaced both the ABS fronts from ABS pump on the white 32 recently as someone had made some pretty average replacements. For example front left ABS ones are 46242-RHR21 (old part 46242-04U00) and non abs for left is 46242-RHR20 (old part 46242-01U10).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, thumbsup from me. The distant shot of the bay just looks same-same as before.
    • Dad had a court case drag out with them from 1998 to 2004. He was in a not at fault accident, NRMA were the ones who covered the other person. They tried to blame his neck injuries on the fact he'd had an injury in 1981 on his extreme lower back where he slipped a single disc right near the bottom. Had been all cleared from that injury for years. This accident destroyed his shoulder, and f**ked a heap of discs in his neck, and he still has major problems with it to this day. Sarah's sister while on her L plates had a small Suzuki Alto, she had stopped to give way to an ambulance, and someone changed lanes behind her because there lane was also slowing, and rear ended her at 80km/h. (She had been stopped for a few seconds already too!). Car was completely f**kED. NRMA sent the vehicle around to 3 different workshops as they kept claiming "We believe it can be repaired, and not written off, we just need to find the correct workshop". It took 3 months, and a lot of arguing before they'd concede and wrote it and paid out. About two years later her sister had a Lancer, someone pulled out of a stop sign without stopping (in an 80 zone). Her sister swerved, hit the front of the other persons car (Instead of dead t-boning the drivers door), which ramped her Lancer, and made it roll multiple times down the road. It hit every panel on the way through. Her sister had slid her self out of the car, and remembers the ambos walking to the accident (They'd been sitting at a set of lights just down the road and witnessed it) and they were saying "Well, this ones going to be a fatality, no way you can walk away from that". Well, she did. And then NRMA sent two assessors out to look at the car, both of which wrote it off. They tried to send another assessor out, except a HUGE uproar was raised, and they FINALLY paid it out. That was on a car, that had damage to EVERY panel, you could see from 100m away the whole car was also twisted, roof bowed etc. Nah, we'll try get out of needing to payout on a $10,000 car... Her sister ended up with major shoulder reconstructive surgery being required, and was permanently limited in her ability to do her job as a nurse after that, as she can't (And was told before surgery too this would be guaranteed to happen) regain full strength in that shoulder. However, there was no choice to not have it, as she could barely use her arm, which was her dominant one, and was in near constant major pain. (And she's the type of person that would try and walk off a broken leg!) NRMA did the biggest run around on the personal injury side too for about 18 months, even to the point of trying to put 100% blame of the accident on Sarah's sister, even though the other driver admitted she didn't look, and didn't stop, and was charged by the police. Sarah used to have a Barina insured with them. It was a policy setup, paid all 12 months in advance. At the end of the 12 months, Sarah was living with me, I reviewed the renewal, it clearly stated "If you do nothing, your policy will cease on XYZ date". We did nothing, as we moved her insurance in with all of mine and I was with Shannons. We find out 10 months later, NRMA decided, because he DAD had a car insurance policy at the same address as what Sarah's mailing address was (Garaged address had been changed), that they'd put Sarah's (What should have been non existent policy) onto her Dad's month to month charges on his credit card. We had to jump through hoops, to get a refund. They didn't care that we actually found the letter that said "If you do nothing, your policy will cease" they made us prove we had NON COMPULSORY insurance else where before they'd issue the refund, and after they agreed to the refund, it still took another 6 weeks and 3 more phone calls for them to actually process it. They also had two insurance claims from storm damage, and they were an absolute cluster to get resolved as well (one vehicle, one house). Some how, up until about 3 years ago, her parents were still loyal to NRMA too, and we were like "How the hell are you so loyal to staying with them, when other places are so much cheaper, and they've f**ked you over every time you've ever had to make a claim?"
    • I got the four AN10 fitting welded up to the cam covers and started up making the head to sump breather/drain lines. The front passenger side cover I used a 45 up top and a 90 at the bottom into the stock VCT head drain spot (3/4" BPST to AN10 adapter) thats unused on the RB25DET NEO with some speedflow flame shield to protect it from the manifolds heat.   back passenger side was a 90 up top with some flame shield and 45 at the sump end. The rear drivers is 45 at both ends   the front drivers fitting is capped off for now but ready to go if i want to try moving the breathers around. I was told by the fabricator to leave all the welds raw for now to make sure there are no pin hole leaks. A lot of cleaning up, re bundling looms and degreasing to go as well as final assembly on the cam cover baffles. The first real test will be 28th March at a Circuit event. added complexity and more spots for leaks but overall looks relatively neat imo
    • Yeah i think the dash needs to come out. To get the loom or maybe just climate control and radio cluster. My mirrors are done i think the motors don’t work so well after flood haha i need the ac fan, you said you wanted to keep it for your 31 and interior loom not including boot. The wiper motor. I’m not sure how good the window surrounds are on the exterior on the pintara.  I will message you to get your bank details shortly 
    • Just another barrier put up to stop cars being modified. When we're all driving Chinese sewing machines, you won't want to modify it anyway, and you'll likely already have slashed your wrists and be locked up in a padded room for your own protection.
×
×
  • Create New...