Jump to content
SAU Community

Recommended Posts

My mechanic is having trouble figuring out where to trim the diff. The problem is the diff will fit int he case but it wont spin, it lock when the diff is in position so it must not make the good contact but he can't figure where it was to be removed because it's not knocking anywhere.

I found these information on the net but it doesn't seems to help me much.. can someone shed some light please ? and/or translate the instruction from nismo in japanese ?

I'm willing to pay for the information, we really need to get that pan installed so we can proceed with the rebuild.

Thanks !

http://www.gtrpwr.com/showthread.php?t=6675

Link to comment
https://www.sau.com.au/forums/topic/458239-how-to-install-front-nismo-diff/
Share on other sites

As in the gears are meshing way too tight and won't turn?

All diff either use shims or threaded adjusters to set pinion depth and pattern.

It shouldnt be that confusing.

Maybe this will help a bit. It shows the shim under the side bearing races etc.

http://www.gtrpwr.com/showthread.php?t=6675

Haha. I linked to your link. Too early for me.....

So it binds up when fully assembled? Is he experienced building diffs ?

what confuse him is that it appears the diff is not ''grinding/touching'' any of my housing ( like if my housing already had the material grinding before..) so he was like '' cool, bolt-on affair! '' but then when we started turning it, it would turn 3/4 and then jam.

What i do is an old school method but may work mate. I paint all the gears turn them and then remove all the gears to inspect the wear or contact pattern. I do that first with the original unit then compare it to what im looking for with the new one. It should be the shim method. This is the rear diff right. ??

Edited by MJTru

What i do is an old school method but may work mate. I paint all the gears turn them and then remove all the gears to inspect the wear or contact pattern. I do that first with the original unit then compare it to what im looking for with the new one. It should be the shim method. This is the rear diff right. ??

Title of the thread says its front diff.

HarrisRacing's build thread has pictures on where to grind material off the sump http://www.sau.com.au/forums/topic/447384-r32-gtr-build-in-usa/?p=7559306

Which is shown in the original post link.

Seriously.

Yes there are 5 places to grind.

4 of them allow the diff to be installed. (Mine simply would NOT go without these ground clear).

The 5th place needs to be relieved so the LSD can rotate. It is the boss for the bolt threads next to the oil pan side. I didn't grind this one enough in the pictures below and the next group of pictures didn't come out clear after I ground it later...but had the same exact issue your mechanic had. You'll see some marking and grinding in the pictures below...the bolt boss wasn't ground enough and the wider diameter of the new LSD wouldn't clear in 4 places of rotation. When you fit it, you can easily see clearance issue (as your mechanic did).

What...you don't have a japanese mechanic? The instructions were very clear (if you know Japanese!) :)

Make sure he gets his shims and preload right! The preload on this front diff is so low it's laughable (AND HARD TO GET RIGHT).

post-136202-0-63656800-1437391408_thumb.jpg

post-136202-0-12309300-1437391449_thumb.jpg

post-136202-0-30789000-1437391476_thumb.jpg

post-136202-0-51418000-1437391615_thumb.jpg

Edited by HarrisRacing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pfft. As if I'd ever point a high pressure washer at my car.
    • The nature of my commute has changed. Way back then it was traffic lights all the way, for ~28km. It sucked. When they finally stitched the expressway together I could do a good 15+km of it at a steady 80-100 with no stopping. That alone has gotten me down to flat 10s. Prior to that it was mid-high 10s. I can't remember the delta that I saw when I got the idle down. It was only ~150 rpm, because the idle speed was never terrible, but for the delta in consumption to be noticeable it would have had to have been at least 0.2-0.3 L/100km - which is not to be sneezed at when it comes for absolute free. It's only about 50L per year, but that's ~$100. A few extra pizzas is always welcome. Note that I have a record of every tank of fuel that has ever gone through my car except for a handful put in by someone else, like my mechanic. I can show you the difference between stock RB20 and tuned RB20, stock RB5Neo and tuned, winter and summer fuel blends, winter and summer fuel blends when the ambient temperature is not appropriate for the blend, working O2 sensor, blown O2 sensor, boosting f**k out of it and frightened to boost it because it is pinging, and so on. OK, I probably can't do all that now with 100% clarity - but at the time when any of those things were in event, you could see it in the records. There's 25+ years of simple tank after tank records, so you have to look for landmarks to work out approximately how old any single record is. What's really important is the meta data and that lives in my head.
    • If you're claiming the issues are not skyline specific, then either the USA is living in the 90s / early 2000s, OR you have the issue of "survivor bias". Which is you're mainly hearing and listening to those with terrible experiences, and haven't found the guys who have cars with good decent builds and no problems. It happens in AU too, that plenty of people keep having issues, and they keep going to the workshops that are known to be shit "because I read on the internet". Even worse, are those who keep posting on the internet as though they know for a fact what something is, when they've never touched/looked at said item in their life, and again are making assumptions, based on something they read, or because it's a certain way in other cars. It's even funnier when those same people debate the facts with the people who've lived and breathed this stuff for over 15 years. Example, I've had someone tell me you can't do something with a Skyline, because they read it on the internet, except I can tell they're wrong, as I did that exact thing back in 2008 with my Skyline.
    • The funniest part I saw, was someone would bitch and moan on FB about something, Andy would be the one to respond, asking for more info, if he could contact them, what the engine setup is, what their config file was, and 95% of the responses were people just going "der! It doesn't work" and Andy going "What doesn't work?" And then going "The firmware!" And they'd go around in circles as no one could ever give information, and Haltech couldn't fault things on the bench, (especially when people wouldn't give any specifics).   Many moons ago, when Andy was back at e420c stage, he reached out to me, and asked me to test different plug and play looms for him (already had an e420c in the car on his V1 PNP loom). And he kept asking me, as I was competent enough to be able to give him some specific feedback on what was/wasn't working, how to replicate the faults etc, and work through things with him. Most people are terrible at answering the questions they're asked, or being able to provide quality feedback other than "it doesn't work".
    • I say it often, none of this stuff is really Skyline-specific per se. But in general there's not a lot of people who actually know what they're doing. A lot of people charging like they do. Agile software development probably isn't the greatest idea for an engine controller.
×
×
  • Create New...