Jump to content
SAU Community

Idle Air Control Valve Help

jet2nv

By jet2nv,
in General Maintenance

 Share

Recommended Posts

jet2nv Mentor

jet2nv

Posted
Posted

Hey guys I'm trying to find out what other cars or company makes this iacv assembly for the rb25det neo as I'd love to buy a generic brand rather then the hi priced Nissan one. Haven't had any luck does anyone know a cross reference part.

23781-AA500 is the Nissan oem

Link to comment
https://www.sau.com.au/forums/topic/458463-idle-air-control-valve-help/
Share on other sites
breaker1845 Community Regular

breaker1845

Posted
Posted (edited)

There are none. Pay for the OEM Nissan one. Plenty of places where they can be sourced at a cheaper rate rather than directly from Nissan.

For the record they are not what I would consider expensive but opinions differ. Do you know that you need an actual replacement IACV to begin with also?

Edited by breaker1845
89CAL Grand Master

89CAL

Posted
Posted

As above

You can easily test the IACV by putting 12V accross the coil. You should feel the solenoid click. If that happens, then likely it is O.K. Mechanically they can be disassembled, cleaned (they clog up with carbon) and put back together. Your only issue might be if a seal gets wrecked/is wrecked, but even then a replacement O-ring wont cost the world

  • 5 years later...
  • 5 weeks later...
discopotato03 Grand Master

discopotato03

Posted
Posted

The actual solenoid is very similar to some Pulsar N14 GA16 ones .

They had two styles , one type actually fits the R34GTt housing . The N14 one uses the same male connector as the R33 RB25DET's and is probably the one to use with Neo manifold/IAC in R33s .

If you need to get the cold start side apart heat the housing/bung with a heat gun . 

  • 3 weeks later...
MoMnDadGTR Mentor

MoMnDadGTR

Posted
Posted
On 13/05/2021 at 12:49 AM, discopotato03 said:

The actual solenoid is very similar to some Pulsar N14 GA16 ones .

They had two styles , one type actually fits the R34GTt housing . The N14 one uses the same male connector as the R33 RB25DET's and is probably the one to use with Neo manifold/IAC in R33s .

If you need to get the cold start side apart heat the housing/bung with a heat gun . 

yes this is a good pointer here, and i might add clean it 10 times after you think you have cleaned it enough. i know its a little different but on my 26 i had a leak from the idle screw on my iacv and this caused it always to idle at 1200rpm. ive since removed and dont use one but yeah make sure you clean the piss out of it, i had success with brake cleaner and air.  cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PLYNX
      Short shifter r34

      By PLYNX · Posted

      Don't do it if your gearbox box has already having syncro issues. The short hifter will put a greater load on them. If you must I remember Nismo did a shorter shifter, with the top part being physically shorter and the part that went into the gearbox was the same as stock. In saying that I've had a C's short shifter (I think) in mine for many years, which was given to me as the previous owner was not sympathetic to the gearbox. Thus forwarned I was careful and had to modify my normal changing style. You have to be super accurate with your clutch and shifts
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Well, after a week of daily driving and having to crawl out between the wheel and the side intrusion bars. I got myself a quick release setup. I went with an NRG short hub and Quick Release with some cute heart cutouts on the pull tabs. Nice and matchy matchy with the rest of the interior accents I have going on.  The only downside is the total stack height even with the short adapter is longer than the old HKB boss kit. Luckily I had some adjustment left on the column so move the wheel away.
    • robbo_rb180
      Short shifter r34

      By robbo_rb180 · Posted

      stock shifter with new bushes, springs and cup will improve it. Gktech do all the bits. The opinion as the years have gone on is the redline is not great in old gearboxes.
    • drifter17a
      Short shifter r34

      By drifter17a · Posted

      Hi all   what short shifter do you use on your skykine r34?   my synchronous does have a problem and i was getting huge delay and grinding sound between 2nd and 3rd, did put shockproof red heavy stuff and it is great now/ no issues   would in your view short shifter screw this up?   people seems to suggest/ use cube short shifter and there is standard and premium. Seen review of premium as much better and less play. Thoughts?
    • GTSBoy
      R34 oil and timing belt change

      By GTSBoy · Posted

      Yeah, there's a bit of a density and friability difference between pebbles and any of those other things. Silicone will definitely float in oil and so will be mobile enough to move around. Although, again, if it is upstream of the filter it really shouldn't go any further. I would only ever worry about silicone when it is in places downstream of the filter. Upstream of the pickup is a whole 'nother matter. We've all seen what that does. I have seen the most abominable crap settled out in industrial gearboxes, trunnion lube systems and the like, without any sign that any of it has touched anything in the machine. Just chilling in the bottom, waiting for the inevitable operator error that causes the whole machine to need to be dismantled for repairs.
×
×
  • Create New...