Jump to content
SAU Community

1995 R33 Gtr Oil In Intake Pipe

judasentinel

By judasentinel,
in Engines & Forced Induction

 Share

Recommended Posts

judasentinel Explorer

judasentinel

Posted
Posted

I have a 1995 R33 GTR, and have been noticing oil coming into the intake pipe between the rear MAF and the rear turbo.

Someone suggested it could be from the exhaust crankcase ventilation (PCV) connected to the rear intake pipe, so I installed a catch can between the pCV and the rear turbo. However, the oil is still showing up in the rear MAF intake hose. I see oil coated on the turbo side of the MAF.

I have twin BOVs recirculating back to the Y pipe between the turbos, and when I rev the engine, I can see the air coming back out of the rear MAF (and not the front). The front MAF and turbo intake pipe are clean, which makes me think that the oil might be coming in from the rear turbo. This theory however, seems to suggest that the rear turbo may be leaking and blown.

However, the car boosts fine, all the way up to 1 bar without any hesitation. If the rear turbo was blown or had issues, would the car still boost? There is no oil leak under the car, and no black or blue smoke coming out of the exhaust. It idles fine as well.

I am totally stumped. I dont want to push the car if the rear turbo is blown, because some people have suggested it might be, but then others say that if it were, I wouldnt be able to boost the car to 1 bar.

Any ideas or suggestions to check?

Please help me as I want to make sure that the car is fine.

Thank you,

Munib

Link to comment
https://www.sau.com.au/forums/topic/459082-1995-r33-gtr-oil-in-intake-pipe/
Share on other sites
djr81 Grand Master

djr81

Posted
Posted

The blowby that gets sucked out of the head by the turbo (As opposed to the drivers side which goes into the engine on over run) goes to the rear turbo. This is almost certainly what you are seeing. Usually it ends up dripping out of the bovs. Even the crack pipe priced Nismo catch can doesn't stop it from happening.

judasentinel Explorer

judasentinel

Posted
  • Author
Posted

So how does one discern if it is the blow-by oil or the turbo is shot/leaking oil from the compressor side? If there is a compressor oil seal leak, will it also go into the intake piping? If so, how do we determine what is actually happening without removing the turbo piping?

Also, if there is an exhaust oil seal leak, will that also cause the oil to come up front of the turbo towards the compressor and go into the intake piping?

Surely, there would be a way to identify if the oil is from the blow-by or the turbo oil seal leak....?

judasentinel Explorer

judasentinel

Posted
  • Author
Posted

In addition to this, I do not see any oil at all in the catch can....maybe a tiny droplet, but that's all. And while the car is running OR I am revving the engine, I do not detect any suction from the catch can into the hose I am running to the rear turbo-MAF intake pipe. If this means the turbo is not spinning, it wont be sucking in any air from that hose, could this also be causing the recirc from the BOV to come out of the rear MAF? When I let go of the accelerator, I can see air/oil blow out of the rear MAF filter. This has me perplexed.

judasentinel Explorer

judasentinel

Posted
  • Author
Posted

If it is just blow-by coming back from the BOVs, and oil is returning with it, why is it escaping though the rear MAF only, and out the rear filter, and getting sucked in by the turbo since the whole point of recirc is to keep the metered air within the intake system?

I dont know if what I am saying makes sense....the BOVs recirculate air, it comes back into the MAF-turbo pipes (through the Y-pipe that connects to both turbos), and ideally, should at stage be sucked back in by the turbos. Instead, it is escaping out of the rear MAF...

fatz Grand Master

fatz

Posted
Posted

If it is just blow-by coming back from the BOVs, and oil is returning with it, why is it escaping though the rear MAF only, and out the rear filter, and getting sucked in by the turbo since the whole point of recirc is to keep the metered air within the intake system?

I dont know if what I am saying makes sense....the BOVs recirculate air, it comes back into the MAF-turbo pipes (through the Y-pipe that connects to both turbos), and ideally, should at stage be sucked back in by the turbos. Instead, it is escaping out of the rear MAF...

That is just because of the stock setup it takes the easy way out

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
    • Murray_Calavera
      Exhaust silencers/varex exhausts

      By Murray_Calavera · Posted

      Nice, let me know how you find the 98 tune
    • GTSBoy
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By GTSBoy · Posted

      Put a hand on an injector and see if that's what the buzzing is. You might be triggering the injectors by moving off idle command.
    • PotatoCake
      Exhaust silencers/varex exhausts

      By PotatoCake · Posted

      Ah, should have been clearer. Currently has a flex sensor installed all good to go.    like u mentioned, I’ve only ever known the car on e85, I might hate 98, but I have to try it out first. Everyone says the -5 turbos get pretty laggy on 98 octane tho…
×
×
  • Create New...