Jump to content
SAU Community

Recommended Posts

Guys for those that are on fb here is link....

https://www.facebook.com/groups/wajcc/702351913200261/?ref=notif&notif_t=group_comment_reply

For those that aren't here is description of ad... Original motor and head

95 v spec. Immaculate inside and out. Bilstein coil overs. Tomei Ti expreme cat back. 3 inch HPI dumps into 3.5 inch front pipe.
Fresh forged built engine with spool rods and cp Pistons and rings. Reimax oil pump gears. Mines cam baffles. HKS 272 cams. Super tech valves guides and seals. Ported head. HKS 1.5mm head gasket. HKS intake and exhaust manifold gasket kits. Garret 2860-5 turbos
Power FC with hand controller. HKS boost controller.
120,000 Ks. All original paperwork. Tomei cam gears
Split fire coil packs

Have 1250cc injectors, nismo afm's, walbro 460 pump and turbo smart fuel pressure reg on order at moment then it's full tune time. (included in Tuned Price).

Built with cp Pistons 86.5mm
Spool h beam rods)
Tomei 1.5mm block oil restrictor
ARP bolts throughout
Nismo copper mix twin plate clutch
Momo Race steering wheel
alarm and immobiliser with shock sensors
keyless entry
Probably lots iv missed

Made 325hp at all 4 on 14psi at 6000rpm limited and 620nm while checking afr's

Comes with stock steering wheel and suspension

$28k with out added parts that are in order mentioned above.

Still on run in tune.
Will be tuned shortly

What do you guys reckon is it a good buy??????

Link to comment
https://www.sau.com.au/forums/topic/459389-thoughts-on-this-r33-gtr/
Share on other sites

Yeah he said it will need a further tune seller said he changed the down pipe to a 3 inhch or somat and its now making 378atws.. I am guessing that figure is still pretty low considering the build hey??? is only done 700kms since build hima nd his mechanic mate did it but he is happy to get me further compression tests results with proof for peace of mind for me

Build without receipts, bring it to Galvsport or similar for a full check imho.
Yeah power was a little low but its running stuff all boost too.
Get it checked over and pay what you're happy with.

Like I said, I personally feel its expensive for a 33.

  • 2 weeks later...

Hey updating this as seller has just got back to me saying he has just had a walbro 450 fuel pump put in and re-tune (2 tunes now) low boost 14psi and high boost 19psi, 19 psi is putting otu 450 bhp atws. does this sound about right???

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Do the R32s run high or low impedance injectors?
    • It may not feel like it to your wallet....but sounds like this was one of those "lucky you did it" rebuilds. Hopefully you have better luck this time
    • It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
×
×
  • Create New...