Jump to content
SAU Community

Recommended Posts

I'm looking to upgrade to something bigger in-tank, but the thought of the noise is a bit off putting. The car is an R33 GTS-T and would be making probably 200-250kw in the near future.

So, very simply, what brand/model of upgraded fuel pump did you find to be acceptably quiet?

And conversely, what pumps did you get that were excessively noisy?

Begin!

First mod I did was to upgrade from stock to Nismo fuel pump, went from inaudible to a slight buzz, and back to inaudible as soon as my exhaust was upgraded, and its a quiet exhaust. The car was a 32gtst not a 33.

I run the E85 Walbro pump, as it's a modern design it's very quiet... it's quieter than my old Tomei pump in my previous R33, however it will heat up your stock wiring like a boss.. I have installed 12gauge wiring from the battery to a 40AMP relay to the fuel pump and earthed the pump directly, bypassing all that FPCM business.

Ive had nearly every fuel pump known to man hahaha, at least 10 different types i can think of, by far the quietest was the Denso 265l/ph intank i just took out of my 33, was silent. The 040 that was in there previously was a bit louder. Happily supported 270 kw. Have just gone to a pair of solid mounted 044's, fed by a pierburg in tank e85 specific lift pump for 350kw +. Could have done it with an in tank, but is now race car so not an issue.

I also had an R34 GTR pump that was barely audible and supported a 250kw SR20. Had a Nismo in tank as well and although you could hear it, wasn't offensive in the slightest. I had a walbro 255 in my R31 and it was pretty noisy?

For the money, denso is the go. Think i paid $150 for my denso new, probably less. Is also straight fit. For your power level i think the walbro 460 is a bit overkill.

Side note: I have an A1000 in another car, and that vid does the noise no justice. It's seriously the loudest fuel pump I've ever heard!

Edited by R31 drift pig

Cool. I think walbro or denso might be the way to go. Anyone know what kinda max power the 265/255 Lph etc can handle?

Depends on a lot of variables, you need good voltage to it with thick wires, and your fuel pressure and boost has a lot to do with flow output.

I would usually expect 300kw on e85 or 400kw on 98 from the Walbro 255's.

External pumps like the bosch 044's need a bit of head pressure on them, quietens them down immensely, and to have no restriction before their inlet, ie being bolted straight to the surge tank with the largest fitting possible, and fitting a check valve in the return line that opens around 20psi (irrelevant though to your question)

The good thing about an intank pump is that its immersed in fuel and generally external to the cars cabin, if its bad enough, a small roll of sound deadener mounted around the boot and tyre well will really reduce the noise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Duh... to answer my own silly question, it's actually described in the FSM... ...400 pages away at the end of the manual, for RB25DE/DET signal descriptions, it cites the TPSwitch signal action, is dependent on the TPSensor value ~ this tends to infer the builtin POT voltage signal is the primary, and the switches are fallback/secondary should the POT fail/TPSensor signal lost (and switch alone with no TPSensor signal allows for base idle speed setting).... makes sense... they (TPS units) used to fail/wear the POT with time, they're not exactly built to last ~ having the switch as a redundancy gets around this...(or, it's less likely both signals would be lost as they're on different power rails)... and of course wrt RB26DETT, you have to electrically disconnect the IACV solenoid from the harness, to defeat idle air control...  
    • Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • They also make them with the motor mounted on the side 
    • Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
×
×
  • Create New...