Jump to content
SAU Community

Recommended Posts

Hey guy's

Need some help? Motor only has 4xxxkm on it but recently when starting after about 3min idling it starts and starts to get warm it's blowing smoke (smells like Oil).

Smoke completely goes once i start driving.. any idea what it could be, valve stem seal??

Car is running on E85

Jayson

Link to comment
https://www.sau.com.au/forums/topic/459923-smoke-issue-when-cold-need-help/
Share on other sites

Sounds like seals.....or what oil are you using?

Oil being pumped up to head but too thick to drain back down until it is warmed up - so its flooding the head.

Another one is go for a drive and find a good sized hill, coast down and take your foot off the go pedal and let the motor suck up oil. When you accelerate away at the bottom is it clear or do you see a smoke plume. A smoke plume [when the motor is warm] indicates rings and/or guides.

There are many types of smoke.

Black smoke is rich.

Blue smoke is oil.

White steam is water evaporating from inside the exhaust when its warming up.

What color is it? (not smell)

Id say its black and running rich while in the warm up circuit.

Stem seals will smoke blue for a few seconds till it gets burned up if its the stem seals.....

E85 attracts a ton of water so cars running E85 tend to have a lot of condensatin, or possibly called "white smoke" coming out the exhaust when idling. Are you sure its not just a lot of condensation mixed in with normal car smells?

Edited by sonicz

E85 attracts a ton of water so cars running E85 tend to have a lot of condensatin, or possibly called "white smoke" coming out the exhaust when idling. Are you sure its not just a lot of condensation mixed in with normal car smells?

Maybe his E85 has absorbed a shit load of water in the tank and running as a steam engine. :P

  • Like 2

when starting after about 3min idling

Bad skyline owner. Bad! No!!! *hits nose with newspaper*

idling a cold engine causes additional wear, when idling so little heat is being produced it takes the engine ages to warm up. The more time spent "running cold" the more wear and blowby is happening.

start it, let it idle for 10 seconds to get oil pressure and then drive it gently (light throttle) staying under half redline (3500rpm).

hmmm, if it takes 10 seconds to get oil pressure then im sure you will know about it in less than that.

I agree that whith idling extensively is no good, but are you trying to say that oil doesnt do anything until up to operating temp?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...