Jump to content
SAU Community

Recommended Posts

Make: Nissan
Model: 350Z
Body Type: Coupe (2 door)
Year: 2003
Kilometres: 130000
Transmission: Automatic
Drive Train: Rear Wheel Drive
Fuel Type: Petrol - Premium Unleaded
Colour: Silver
Air Conditioning: Yes
Registered: Yes
Registration Number: 1BZ 1QY
Registration Expiry: 10 months - 21/08/2016
Variant: TOURING
Location: Victoria
PRICE: $12,000



After a quick sale. wife is now pregnant hence lowering price. No this is not a P plate legal car. No more joy rides unless a deposit is paid or a qualified mechanic wishes to check car apon sale.


$12k firm - dont bother bargaining as this is the cheapest on the market already.


Cleanest and cheapest tip tronic 350z for sale in Melbourne. Please do not hesitate to inspect other 350z before inspecting this immaculate one. Price listed cheap due to not wanting to deal with time wasters. Priced to sell to genuine buyer. 1 full years rego. Just paid in advance. Dont have time for time wasters.


This Nissan 350Z 2003 has electronic brake force distribution (EBD). It has limited slip diff (LSD), Original Bose headunit and 7 BOSE speakers and subwoofer, heated leather seats and sports instruments. This car has cruise control, 17" alloy wheels, remote central locking, brake assist and sports pedals.


Car has aftermarket coilovers installed. Paid premium when new - Megan adjustable coilovers - has in cabin adjustable dampener - paid over 2k - car will also be sold with stock suspension as well.


Aftermarket Xforce Invidia Q300 exhaust system fitted to car - Paid 1.7k brand new - car will also be sold with stock exhaust as well - One of the best exhaust systems you can have on your 350z. No cheap chinese made loud droning noises.. perfect purr


Front and Rear GKtech 35mill spacers - purchased brand new - $200 a pair


Car always garaged and serviced. Serviced every 5000km by professional.


Car will be sold with standard 17" nissan wheels. 19" Varrosteon will not come with car. Wheels are now sold.


Alot of spare parts available with sale of car - rare 350z premium spec mud shield splats. another set of 350z headlights - was going to spray insides black but never got the time. Ultra rare v35 mud splat (all four corners) as well - very hard to find.


Only available for inspections after 6pm weeknights and all day weekends.


Please call and arrange time in advance as I work on shift.


No joy rides.


Contact me on 0401762756 . Please leave voicemail message if I cannot answer your phone call *** i do not check this site often so call me**


Will not be responding to emails. If you are interested. Call me or text with a valid Australian phone number.

post-23318-0-93200400-1443928781_thumb.jpg

post-23318-0-13512900-1443928786_thumb.jpg

post-23318-0-88336200-1443928789_thumb.jpg

post-23318-0-70758400-1443928794_thumb.jpg

post-23318-0-60759000-1443928798_thumb.jpg

post-23318-0-25479600-1443928809_thumb.jpg

post-23318-0-02325700-1443928814_thumb.jpg

post-23318-0-47495900-1443928818_thumb.jpg

post-23318-0-87006400-1443928825_thumb.jpg

post-23318-0-37797600-1443928830_thumb.jpg

post-23318-0-30490000-1443928837_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...