Jump to content
SAU Community

Round 7 - Phillip Island


ssxRicho
 Share

Recommended Posts

Yeah we were both running very similar times, had spoken to him couple of times just to make sure we're not getting in each others way. He was a very consistent cornerer, so we were having some fun together. Sometimes it did get a bit close though :P

Link to comment
Share on other sites

Grabbed what I think is the complete list of guys from SAU off natsoft, was some good times in there with plenty of PB's. :)

Skylines Australia Vic Aaron Barnes Nissan R35 GTR 3800 D S25 1:46.8744
Skylines Australia Vic Matthew Borci Nissan Skyline GTR 2600 H S34 1:48.6266
Skylines Australia Vic John Olasau Nissan Skyline GTR 2600 D S37 1:49.5913
Skylines Australia Vic Matt Lowth Lotus Exige S 3500 D S22 1:49.8926
Skylines Australia Vic Huy Phan Nissan 200sx 1999 H S35 1:51.0517
Skylines Australia Vic John Packham Nissan 200sx S14 1998 D S28 1:52.7485
Skylines Australia Vic Brett Stuchbery Holden Commodore VX 5700 H S22 1:53.1849
Skylines Australia Vic Darren Cox Nissan Skyline R32 G 2568 H S34 1:53.8790
Skylines Australia Vic Ben Johnson Honda S2000 1998 B S6 1:54.1746
Skylines Aust - Vic Peter Vakras Nissan Skyline 2600 H S7 1:55.2008
Skylines Australia Vic Jason Mcdonald Nissan 200sx 5665 H S36 1:56.0742
Skylines Australia Vic Andrew Cutropia Datsun 1200 1998 I S28 1:57.0449
Skylines Australia Vic Leslie Maslaris Nissan Skyline R32 G 2000 B S12 1:58.0093
Skylines John Magar Nissan R33 GTR 2600 H S11 1:58.5328
Skylines Australia Vic Simon Henman Nissan Skyline 2498 D S35 1:59.8862
Skylines Australia Vic Gavin Hately Toyota 86 1998 F S33 2:02.6950
Skylines Australia Vic Adam Birdseye Nissan R33 GTS-T 2498 H S30 2:05.6481
Skylines Australia Vic Alex Pirpiris Honda Integra 1800 B S21 2:10.9265

Edited by Brett SS
  • Like 1
Link to comment
Share on other sites

 Share




  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...