Jump to content
SAU Community

Recommended Posts

^you will be more likely to rub the tyres due to increased diameter and speedo will also be out. I run 265/35/18 and they are just about right. If I was to go 275 or bigger I would be going with a 30 profile. Use a tyre size calculator on the webz and try to match the factory rolling diameter as close as possible with your new size.

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620001
Share on other sites

According to ADRs and other stupid rules your apparently not allowed to fit a rim greater than 1" width and 1" diameter over stock. Sigh. I guess that's why most of us keep a set of some sort of stock rims just in case. but hey who could be farked getting defected.

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620005
Share on other sites

What's the issue with increasing rolling diameter. I though what's important was to keep all 4 tyres the same size for the awd

yep, you need to keep all 4 wheels the same rolling diameter, you also want to keep this rolling diameter the same as factory.

your answer has been given, if your at stock height then it will fit but will not be ideal, your gonna have an incorrect speedo

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620014
Share on other sites

yep, you need to keep all 4 wheels the same rolling diameter, you also want to keep this rolling diameter the same as factory.

your answer has been given, if your at stock height then it will fit but will not be ideal, your gonna have an incorrect speedo

Apart from incorrect speedo the 40 profile will it rub under normal driving conditions?

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620032
Share on other sites

According to ADRs and other stupid rules your apparently not allowed to fit a rim greater than 1" width and 1" diameter over stock. Sigh. I guess that's why most of us keep a set of some sort of stock rims just in case. but hey who could be farked getting defected.

I believe we have 2" increase as the 33 ways more than 1400kg

FWIW guys, at least in SA, they do not actually still go by those old rules regarding a fixed number of inches increase in wheel width or wheel diameter. So long as the % change in rolling diameter is inside the limits you can do any diameter change you like. So that comes down to availability of suitable profile tyres. Same with the width. So long as track is not out of spec and wheels/tyres do not poke or have interference problems, you can have as many inches extra as you like.

Of course, practically this often works out to being not much difference to the old blanket rules anyway.

So while I know this to be the case in SA, it may or may not be in other states. But it was my understanding that most of the other states are being equally realistic about it these days. The old rules were written in simpler times.

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620160
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
    • You can probably scrub the rust with a toothbrush or something. After you get the rust off flush well with water to neutralize and you will probably want to also use a fuel tank sealer to keep it from rusting again.
    • The sodium citrate solution is designed to buffer the citric acid to keep it from attacking metal quite so much, the guy that came up with that recipe did a ton of testing on how much metal loss occurs over time and it's nothing crazy unless you forget about it for months:   
    • Ohhh I see lol To be honest the main reason why I wanted to start modding is because of a business trip to Japan and Indonesia. I saw many cool and modded cars all throughout in these countries, especially Japan. I myself am of Chinese+Japanese nationality and when living in china (never lived in Japan js my dad side lol) I remember staring at these cars pass by with their loud tacky exhausts and insane wide body kits. And when I went back to Japan, I got even more invested even asking people about their cars and why they modded. Most gave similar answers to what you said but funny enough one guy just said that he saw the need for speed movie being filmed once in Tokyo I think near Shibuya Crossing and got inspired to tune and mod. After that I just started to fantasize on owning a car like that. Also tbh I prefer the R32 over the R34 it's just the R34 is more iconic lol (also apparently better aftermarket support than the R32) and my only goal really is just to make the car mine and make it fun to drive. As much as I love my Cayenne it's pretty bland to drive. Sure the interior is nice and pretty, gives you attention yada yada but I've wanted to experience what it is like to have a car that is truly yours. I suppose thats the goal so far. Haha if you find where I'm from, then sure. Ill help you out on your next "financial decision"
×
×
  • Create New...