Jump to content
SAU Community

Recommended Posts

^you will be more likely to rub the tyres due to increased diameter and speedo will also be out. I run 265/35/18 and they are just about right. If I was to go 275 or bigger I would be going with a 30 profile. Use a tyre size calculator on the webz and try to match the factory rolling diameter as close as possible with your new size.

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620001
Share on other sites

According to ADRs and other stupid rules your apparently not allowed to fit a rim greater than 1" width and 1" diameter over stock. Sigh. I guess that's why most of us keep a set of some sort of stock rims just in case. but hey who could be farked getting defected.

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620005
Share on other sites

What's the issue with increasing rolling diameter. I though what's important was to keep all 4 tyres the same size for the awd

yep, you need to keep all 4 wheels the same rolling diameter, you also want to keep this rolling diameter the same as factory.

your answer has been given, if your at stock height then it will fit but will not be ideal, your gonna have an incorrect speedo

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620014
Share on other sites

yep, you need to keep all 4 wheels the same rolling diameter, you also want to keep this rolling diameter the same as factory.

your answer has been given, if your at stock height then it will fit but will not be ideal, your gonna have an incorrect speedo

Apart from incorrect speedo the 40 profile will it rub under normal driving conditions?

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620032
Share on other sites

According to ADRs and other stupid rules your apparently not allowed to fit a rim greater than 1" width and 1" diameter over stock. Sigh. I guess that's why most of us keep a set of some sort of stock rims just in case. but hey who could be farked getting defected.

I believe we have 2" increase as the 33 ways more than 1400kg

FWIW guys, at least in SA, they do not actually still go by those old rules regarding a fixed number of inches increase in wheel width or wheel diameter. So long as the % change in rolling diameter is inside the limits you can do any diameter change you like. So that comes down to availability of suitable profile tyres. Same with the width. So long as track is not out of spec and wheels/tyres do not poke or have interference problems, you can have as many inches extra as you like.

Of course, practically this often works out to being not much difference to the old blanket rules anyway.

So while I know this to be the case in SA, it may or may not be in other states. But it was my understanding that most of the other states are being equally realistic about it these days. The old rules were written in simpler times.

Link to comment
https://www.sau.com.au/forums/topic/460372-will-this-rub/#findComment-7620160
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...