Jump to content
SAU Community

R34 Gtt Rb26 Swap Wiring Help

Eisen

By Eisen,
in General Maintenance

 Share

Recommended Posts

Eisen Newbie

Eisen

Posted
Posted (edited)

Hello everyone,

I'm swapping a rb26dett engine in my r34gtt and need help with the wiring. Has someone done this before me or does someone know wich wires I musst put together?

My plan is to run the original neo loom for all bodythinks line lights abs wiper and so on, and the rb26 loom only for the engine.

I will be thankfull for every help

Edited by Eisen
Link to comment
Share on other sites
  • 1 year later...
6BANGER Enthusiast

6BANGER

Posted
Posted

Hey mate did you end up doing the engine swap? 

I have a R34 GTR RB26 in my GTT and currently running the RB26 engine loom and GTT body loom just like you mentioned.

Engine starts and drives but I have the ABS light on due to the left wheel speed sensor.

 

Link to comment
Share on other sites
  • 2 weeks later...
6BANGER Enthusiast

6BANGER

Posted
Posted (edited)

Yes, the left wheel speed sensor is connected in the engine bay. However, the wiring loom near the ECU uses different connectors between the GTR and GTT. 

I was hoping someone can shed some light into how the GTT body loom can be connected to the GTR ECU. 

Edited by 6BANGER
Link to comment
Share on other sites
DanielH Community Regular

DanielH

Posted
Posted

I swapped an r32 rb26 into my na r34 and just used the neo engine wiring loom with minor changes like tps and cas plugs. Much easier to just use the rb25 loom with a tuneable ecu.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DraftySquash
      Question about R34 GTT A/T Solenoids

      By DraftySquash · Posted

      So.... when I'm finally getting around to having my power steering leak sorted, now it looks like I've got the same issue most A/T Skylines are having. My A/T light will randomly come on and I'm stuck in 3rd gear until I turn the car off and on again. Only 3 weeks ago I did a complete transmission service: Oil flush + new gasket + new filter. This came out of nowhere!! It wasn't like the car was driven hard. I drove about 3 mins down the road to get fuel and boom!!!  Anyway, I have a few questions and hope you fine people can help me out here. All questions are in red. 1. The solenoids: I was looking at the parts catalogue in Amayama and I could only find the Solenoids as an assembly. https://www.amayama.com/en/part/nissan/319404ax05 I read in another thread that Solenoid A = 31940-4AX02 & Solenoid B = 31940-4AX05 but the Amayama product has only the code of B. Is this the right part? Can anyone who has done the Solenoid changes or seen them confirm if this is the complete set of A & B?   2. Gasket and Filter: I'm not going to try change the solenoids myself because it seems difficult to do in a home garage with just 2 jack stands. I plan to take it to a shop and get it changed. I was also going to buy the transmission sump gasket at the same time so I don't reuse the same gasket. Should I just use the existing gasket as it has only been on the car since OCT 19th? (~3 weeks) Should I be buying a brand-new gasket and a filter? Does this job involve taking the filter out?   Thanks in advance to everyone. It's hard to find a video of someone doing a solenoid change on a R34 so any help you can give answering my remaining questions would make me less stressed.
    • Kinkstaah
      R34 GTT RB rough idle problem with weird RPM gauge fluctuations

      By Kinkstaah · Posted

      Yea - From what I have seen from the video, the car idles like any R34 lol 50PSI of fuel pressure is hardly super abnormal, the regulator is working because the pressure remains static when the throttle gets revved, i.e pressure remains the same when manifold vaccuum changes. Bigger pumps on stock rails always bumped the pressure in the rail without using an aftermarket regulator to change that. Do you know what your IAC is actually doing? Has there been any data showing the stepper motor % etc? There's no way your idle is actually moving around the way the cluster(s) are indicating. You would hear the difference with the engine RPM flying to 3k and 1k in mere seconds. I'd be checking the wiring to the tacho. What the tacho is telling you and what the engine/ecu is telling you are different things. I assume your ECU doesn't display the spike. So whatever is telling the tacho to be at X rpm is doing something weird. When the going gets insane, you're on the wrong path. You've ruled out plenty of things that are working correctly/aren't the issue. Your idle isn't doing what the tacho is indicating. You have two seperate issues, I don't think they are linked, and the idle seems reasonably okay unless it's stalling which.. well, it hasn't. Troubleshoot the stall if it occurs by figuring out what your IAC is doing vs what it is being told to do.
    • PranK
      R’s Meet - Fuji speedway 2024

      By PranK · Posted

      So awesome! I love the RB with the exhaust on display.
    • Just_a_datsun
      RB26 R32GTR Block. Z32 5spd Turbo Gearbox.

      By Just_a_datsun · Posted

      NO HITS PRICE DROP   ENGINE - $8.5k ONO TRANSMISSION - $1.8k ONO  
    • GTSBoy
      ER34 RB25DE Auto - Would a flush ever fix an "A/T" light?

      By GTSBoy · Posted

      If it has had a code in the recent past, the code should still be there waiting to be read.
×
×
  • Create New...