Jump to content
SAU Community

Recommended Posts

5 Speed manual gearbox, out of a r32 GTSt.

Approx 100,000 kms when removed from car. Is in PERFECT condtion ie no grids, scrapes, or notchy gears.

Suit rb20, or for 5 spd. conversion. Holds up to approx. 250rwkw. Replaced due to large HP application.

Comes with (if you wish) : 2 piece tailshaft (std), centre bearing (as new), and cross member.

SELL ALL FOR $450 - WILL SEND INTERSTATE

Pm me for ANY questions....

Link to comment
https://www.sau.com.au/forums/topic/46163-rb20det-5-speed-manual/
Share on other sites

Its only about a hundred dollars or so. If you like i can find out exactly how much, and let you know monday. Whatever it costs to send to you, knock half the cost off of the $450. So (if it was $100) - for $450 i'll send it to your door, ie i pay for half the transport cost. ($400 for box, + $50 for postage)

make any sense?

no clutch, or slave, yes it has a shifter. I can organise the slave when i get the r33 one swapped over with the std r32 on thats in the car now. Should be ok to get the slave in about a week or so, but the rest is out of the car.

no clutch, or slave, yes it has a shifter. I can organise the slave when i get the r33 one swapped over with the std r32 on thats in the car now. Should be ok to get the slave in about a week or so, but the rest is out of the car.

cool, i meant "clutch slave cylinder" not "clutch & slave". :)

Let us know how you go with the freight quote, thanks.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...