Ignition Break Down Beyond 18psi In My Rb32dett

[GT-SPEC BNR-32]

Hi all,

I have recently had my BNR32 Vspec tuned.

Its set up includes stroked 26/30, 3.2L with twin low mount Trust t618z-10cm's.

The power made was 559.7hp atw on 18psi. The ignition started to play up, as they are the original coil's.

Question? What will I have to do to make a HKS twin power with BNR34 harness work in a RB26 from a BNR32? is it as simple as installing the Twin power to some R34 Coils and plug the harness in?

Any advice from experience would be greatly appreciated.

[Piggaz]

Talk to Yavuz or Mark about running a Morristech 6 channel ignitor. It's much cheaper than a twin spark and actually does something.

[Ryno]

Another option that may work out cheaper would be to swap to LQ9 (LS truck) coils.

Great looking car by the way. Where did you get the bonnet from? It's a style I haven't seen before.

Edited January 6, 2016 by Ryno

[XKLABA]

D585 LS2 truck coils, www.ls2rb.com, bit of wiring to remove ignitor and more spark energy you should ever need

[sneakey pete]

Just put in not decades old stock coils?

[r32-25t]

Just put in not decades old stock coils?

this or splitfires, sometimes we need to not make mountains out of mole hills people

[KPCresta]

this or splitfires, sometimes we need to not make mountains out of mole hills people

Splitfires FTW! They are a proven product that can handle a high hp setup.

[R31Nismoid]

Even with 3200cc those turbos aren't all in till 5000rpm? Good golly they are such rubbish.

Anyway, as others have said - try out fresh stock coil packs first. If problem persists, go after market if replacing at your power level. Might as well

HKS DLI was good 10 years ago, but the world has come a long way and there are better/cheaper offerings out now.

[Ke55pig]

They also no longer have any hks dli for 34s

[Piggaz]

Proberbly a good thing.

[GTSBoy]

D585 LS2 truck coils, www.ls2rb.com, bit of wiring to remove ignitor and more spark energy you should ever need

this or splitfires, sometimes we need to not make mountains out of mole hills people

Well, these two solutions are, in order from the 2nd quote upwards, 1) the easy good workable solution and 2) the bit more difficult, bit more involved but technically better solution that really doesn't cost much more and is highly recommended for those who intend to lean hard on the boost.

You makes your choice depending on how much effort you can put into it vs your intended usage model.

[Piggaz]

Don't forget to replace your 25 year old crusty/burnt coil pack loom.

[Dose Pipe Sutututu]

Don't forget to replace your 25 year old crusty/burnt coil pack loom.

Wiring Specialities do a replacement loom for less than the OEM loom and I dare say is of the same quality if not better

Both non braided and braided versions too.

http://www.wiringspecialties.com/wisprbcohabr1.html

[GTR_JOEY]

Handy link^^

[kingtube69]

Wiring Specialities do a replacement loom for less than the OEM loom and I dare say is of the same quality if not better

Both non braided and braided versions too.

http://www.wiringspecialties.com/wisprbcohabr1.html

God damn the RB25 one is cheap - Do you know what they are like with shipping mate? i.e will they ship to Aus/is it expensive to ship?

Cheers

[Ryno]

I've got a full engine loom arriving from them next week. Shipping wasn't too bad as they use USPS.

[XKLABA]

Well, these two solutions are, in order from the 2nd quote upwards, 1) the easy good workable solution and 2) the bit more difficult, bit more involved but technically better solution that really doesn't cost much more and is highly recommended for those who intend to lean hard on the boost.

You makes your choice depending on how much effort you can put into it vs your intended usage model.

Cost $480 for everything with new coils and an hour with the soldering gun, had the whole conversion done in an afternoon

[R31Nismoid]

Wiring Specialities do a replacement loom for less than the OEM loom and I dare say is of the same quality if not better

Both non braided and braided versions too.

http://www.wiringspecialties.com/wisprbcohabr1.html

$100? What's delivery? + exchange rate, sounds like it'd be more?

OEM from Nissan AU is only $140... Well, that's what I paid when I got mine for my RB26 5 years ago, I doubt it's gone up too much in price.

[GTRNUR]

I use Ignition Project / Plazma direct coils as a bolt in solution that uses an OEM loom. That and copper BCPR-7ES plugs gapped at 0.65, no sign of ignition issues at all. 705hp atw.

[Piggaz]

Cost $480 for everything with new coils and an hour with the soldering gun, had the whole conversion done in an afternoon

image.jpeg

Looks great, King of the Hill