Jump to content
SAU Community

M35 Vq25det Greddy Ultimate Ecu Wiring Install

BoostdR

By BoostdR,
in Four Door Family & Wagoneers

 Share

Recommended Posts

BoostdR Mentor

BoostdR

Posted
  • Author
Posted (edited)

Seconded. My cheap sensor is junk up top. Very noisy on boost. Varies 4-5psi. I feel this has a lot to do with the plenum pulses. A HPX-N1 MAF would be my preferred option. Since resolution would be more than enough and plenum pulses wouldn't be a factor. Map filtering works but gives lazy response (worse than MAF response due to the inlet track)

Edited by BoostdR
Link to comment
Share on other sites
  • 4 months later...
BoostdR Mentor

BoostdR

Posted
  • Author
Posted
Hi All,
As promised here is a copy of my install notes. Water temp is external as I found the OEM sensor signal to skew when tapped.

Innovate LC-2 wide band is used for narrow band emulation and EMU autotune

Vehicle setup: VQ25DE OR VQ35DE
Speed pulse: TBA(think it was 16pulse, 21% correction)

If someone has spare time and wants to put this info in a neat spreadsheet please go ahead.

Matt

post-49288-14532520652612_thumb.jpgpost-49288-14532520809067_thumb.jpg



EMU Earth isn't to pin 106 it should be pin 47

Link to comment
Share on other sites
  • 6 months later...
  • 3 years later...
ProjectStag1 Rookie

ProjectStag1

Posted
Posted

Hey guys, tried my Emanage install and seem to have blown up the unit. No power after running for a while, got a red light then died

 

anyone got a spare unit? Or know if repairers in Sydney?

 

Link to comment
Share on other sites
ProjectStag1 Rookie

ProjectStag1

Posted
Posted
On 27/05/2020 at 4:15 PM, ProjectStag1 said:

Hey guys, tried my Emanage install and seem to have blown up the unit. No power after running for a while, got a red light then died

 

anyone got a spare unit? Or know if repairers in Sydney?

 

Found one - Let install pt.2 begin..

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Count Grantleyish
      Vic Wasteland Thread - 15.0

      By Count Grantleyish · Posted

      People still have Skylines? I thought they're non-existent now. 
    • pogman
      George's R33 GTST build

      By pogman · Posted

      Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • GTSBoy
      Hello Everyone

      By GTSBoy · Posted

      They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • Triple OG
      Hello Everyone

      By Triple OG · Posted

      I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • r32-25t
      GReddy Injector Help!

      By r32-25t · Posted

      Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...