Jump to content
SAU Community

Recommended Posts

Located In Ballarat, VIC

Will post most parts at Buyers expense

****RB30 Parts****

R31 Auto Gearbox Computer (Located under passenger seat)
-A64-000 J29 $10 ono
-A64-000 J41 x2 $10 each ono
Charcoal Canister $20
Power steering Res $20
Idle Air adjust with FICD $20
Pressure Reg – Solenoid Valve $20
Air Reg x2 $10 each
Coils x4 $10 each
Pressure Reg $10
Throttle body x2 1Missing the Throttle cable connector $10 each
Throttle cable holder Block bracket $5
Starter Motor $25
R31 Rad $30
RB30 Flywheel - Has surface rust $40

****R31 Outside Parts****

Chrome Door Handles – All Except Drivers Side $30
Black Door Handle – Front Passenger side $5
Bonnet Hinges Both Left and right $5 each
Fuel Cap $5
Front Bar Indicators – Both sides $10
Chrome Strips that go above the top of the doors – both sides $30
Side Indicators – Both sides $10
Wagon Drivers Side Tail light $10
S3 Headlight Drivers Side $20
S3 Headlight Passenger side x3 $20 each
S2 Headlight Drivers Side $25
S2 Headlight Passenger side $25
S2 spot lights $30
S2 Filler Bar $10
S2 Bonnet - Needs repaint - $30
S2 Rear Bar & Reo $30
S2 Passenger Gaurd x2 $20 Each
S3 Passenger and Drivers Side Gaurds $20 each
S3 Rear Bar $30
LSD - Needs Rebuild $30

****R31 Interior Parts****

Ash tray - $5
6 Gauge Cluster $30 - not sure if works
Random grey dash buttons - Let me know what you after
Grey dash - $20
Indicator/Headlight stork x3 $20 each
Wiper stork 1x Adjuster $20 x1 Non Adjuster $10
Other random stuff

Link to comment
https://www.sau.com.au/forums/topic/462392-r31-nissan-skyline-rb30-parts/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
    • Awesome writeup and details. Thanks for sharing the story so far. I can relate to parts of it with my previous car and some of the issues I had to deal with.
×
×
  • Create New...