Jump to content
SAU Community

Damaged R32 W/rb25 - Need Gone

inmaniac
 Share

Recommended Posts

inmaniac Community Regular

inmaniac

Posted
Posted

Hey all,

Got into a prang with my R32 GTST. As per pictures, it was a front-on collision that took out the front bumper completely, all front lights, radiator and a few other bits.

Looking to get rid of it ASAP.

The engine seems fine, starts instantly, and the car can still move (note I don't say drive). The steering is fouled by the damage.

Specs:
RB25DET w/ roughly 170,000kms

RB20 5 speed

Z32 ECU w/nistune

Ebay turbo (was working fine on 12psi)

GTR pump

I am NOT parting the car, selling whole.

Best offer by Friday 29/1/16 can take it, I need it gone. Car is located in Guildford 2161. PM if interested.

Thanks for your time.

213d0f5098.jpg

9b384883bd.jpg

06eec6a5cf.jpg

879b78cce5.jpg

70276d8182.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • elohim_imanu
      Removing sump

      By elohim_imanu · Posted

      I did manage to do this without removing the engine or front cross member, but I had the advantage that the exhaust manifold was removed. I am not setup to support the engine from the top or remove it. 1. Loosen the engine mount nuts so they only have a nut of thread. If it is a manual, I think you have to remove the gearbox to engine support brackets. 2. Jack up the engine off the bottom idler mount. Jack it up till the end of the slot and nut on the mount. You need this clearance to get the pan out at the rear of the engine. 3.Break the sealant seal to sump. I found a oil pan separator tool helpful to get it started. 4. The oil pick up can be removed with the gap available.  5. The oil pan can be removed now. 6. Before assembling, do not apply sealant to the oil pick up area as your hand will rub it all off but apply to the other three and a bit sides. 7. It is a two man job to put the oil pan back, with the sealant, as you do not want it to touch anything and rub off. 8. With one person supporting the oil pan the other can fit the oil pickup 9. Apply the remaining sealant. This would be more difficult with the manifold or turbo in place, but I think it could be done. As you can see my sealant is a bit ugly, but good enough to seal. 10. Lift the sump up to the engine and bolt it on. We found it was easier to use two long guide bolts at each end to get it nice and aligned without touching.
    • MBS206
      Rob's S Chassis track cars. Now with more s15 and less 180sx

      By MBS206 · Posted

      I find building an exhaust a really satisfying job! Looks nice!   Did you consider using an oval pipe to get the same cross sectional area but keep it above the chassis rail?
    • Murray_Calavera
      Never ending fuel pump drama

      By Murray_Calavera · Posted

      @Dose Pipe Sutututu Sounds good.  Just double checking with the pull up resistor indicated in haltech's info sheet for their SSR - https://www.haltech.com/product/ht-030202-solid-state-relay-100-amp/  I'm guessing that would only be if the ECU did not have an internal pull up resistor? Their instructions are pretty strongly worded lol "1K pull-up resistor MUST be fitted." 
    • Dose Pipe Sutututu
      Never ending fuel pump drama

      By Dose Pipe Sutututu · Posted

      I wouldn't think you would need a flyback diode, as it's an OEM replacement parts for a fan controller/relay on a Dodge. Another tried and tested option are the Volvo XC90 (or similar) fan controllers.   
    • Murray_Calavera
      Never ending fuel pump drama

      By Murray_Calavera · Posted

      Just checking, with this would you need anything else to get yourself up and running? Do I need a flyback diode, pull up resistors or anything else?
×
×
  • Create New...