Jump to content
SAU Community

Recommended Posts

As instructed ........

What is everyone's thoughts?

  On 13/02/2016 at 9:08 PM, Rickyv42 said:

Just got my car tuned 703rwhp 524rwkw. Does anyone know the record for these turbos?
Built bottom end with 87mm pistons
2860-5 turbos
Pon cam type A
Tomei manifolds and dumps
Apexi down pipe
ID1000s and tomei fuel rail
2 walbro 400lph fuel pumps
Nismo inlet pipes and hard intercooler pipes
Custom intake pipes
AEM series 2 ecu tuned for flex fuel
4CA2765D-A61C-43E6-9DCF-9E05E902C893_zps

Edited by Jc052685
Link to comment
https://www.sau.com.au/forums/topic/463036-rb-2860-5-highest-hp/
Share on other sites

Simply a dual 2.5" Maf-less system I built for it. I am wishing now that I used 3" as I may have left a few hp on the table. I welded 2.5" v-bands to the turbo inlets as to minimize the inlet turbulence that a couplet could induce. Took care to make sure all inlet pipe fitment was perfect.

00000000-0000-0000-0000-0000000000ED_zpsA7AF15C8-183C-4845-B030-E13041C0BC9E_zps

I personally feel that if the customer wanted to truly max out the turbos by freeing up some restriction that still exists in the inlet & charge pipe sections that I could get another 25-35whp out of them. Car is still on the factory intercooler & intake plenum after all.

These are all the performance mods I can remember.

CP pistons 87mm

Eagle rods

N1 crank

Nismo oil pump

Mild head work

BC springs/retainers

Tomei type A poncams

2860-5 turbos

Tomei dumps

Tomei manifolds

Spec twin plate

AEM ecu tuned for flex fuel

Nismo thermostat

Apexi down pipe

Aluminum Radiator

ATI dampner

Blitz cat back

Greddy cooling panel

Greddy timing belt

ID1000 injectors

Tomei fuel rail

2x Walbro E85 fuel pump

Nismo air inlet pipes

Nismo intercooler hard pipes

Powerfab intakes

Splitfire coil packs

Got a pic of the cooler, Nismo is not factory and there is two versions with one being far superior to the other

Looking at the parts list I would say the exhaust and ID1000s are the most limiting factors and would guess a realistic 400-420rwkws and give or take 130-135mph

  On 18/02/2016 at 2:50 AM, XKLABA said:

List says Nismo cooler, factory cooler starts to measurably pressure drop from around 350kw, 500+rwkw on a stock cooler is where I call mythbusted

Nismo intercooler hard pipes

Car made 490whp on 13psi...... Mustered a 507whp pull at about 15psi but the 93 octane pump gas was the limiting factor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • 500-600hp into a RB is already 'sinking endless amounts of money' into an engine. Especially a 30 year old engine. Unfortunately this is the RB Game. Considering stock power (or at least stock components) will do ~360whp on 98 by simply turning up the boost on the stock gear on a RB26, that would be where I'd say the cutoff point for "sinking endless amounts of money into the engine" Cause to even do this reliably you'd probably need to replace all the bits anyway cause they're old, starting your sinking journey anyway. I reckon the least painful way is rebuilding the engine to make 50hp over stock lol. The 'plan your ownership around a rebuild' was a common saying 15 years ago.
    • Well, the NA RB25 is nothing special in terms of the amount of power it makes stock, nor with any easy mods like extractors & exhaust, opening up the intake tract, etc, etc. And just like any small capacity NA engine, getting lots of power out of them takes a fair bit of money and, depending on how far you go with big cams and high compression and so on, quite grumpy to drive. So, boost is the answer. Many many many of them have had a turbo added. This is easy enough. Same as for any engine. Need the things you need to bolt on the turbo of choice, fuel system and management upgrades, clutch, stronger gearbox ( you do not want to run a boost RB25 through the NA box), diff, brakes, etc, etc, same as you would for most other NA+T things. Some much smaller number have had a supercharger added instead. These are good and cool, but have nowhere near the potential of the turbo route. All the same required upgrades apply. So, potential? Anywhere from not much to quite a lot, depending on how much effort and expense you want to go to. Is there value in the effort and expense? Objectively, no, there is not. If you're gaining enjoyment and don't mind blowing a lot of money on the project, then that's where the value is. Parts? Nissan dealers for some. Many many on-line vendors who do Japanese manufacturer spares (buy buying them from disposals at dealers around the world, direct from manufacturers, increasingly from Chinese knockoffs, etc) and warehousing them in Dubai or similar places. Amayama, Partsouk, etc etc. There are quite a few. Some local to Australia, some local to Europe, some local to the US. You can upgrade literally everything. For an NA, unless you're going to boost it, there's little point going past a nice exhaust, as I said above. After that (well, actually probably even before that) you should concentrate on making it handle the best it can, good brake components, light wheels and tyres, and just make it something to enjoy throwing through the curves. You'll never, ever win any drag races, so it needs to be taken as a nice point-to-point car. Throw in some Recaros or Brides, nice Momo wheel and gearknob, so it's pleasant to be in (because god knows, the inside of an R33 is not a pretty place!!) and away you go.
    • How many $$$ do you have to slip cams to logbook a car that’s not the orginal to the 1990 standard lol
    • Thanks for the update I truly appreciate it. I was trying to figure out the sensors. 
×
×
  • Create New...