Jump to content
SAU Community

Changing Brake Pads Without Removing Calipers? How To Compress Pistons?

V28VX37
 Share

Recommended Posts

V28VX37 Veteran

V28VX37

Posted
Posted

Hi guys,

This is a really basic question but I can't find a clear answer: Is there a good way to change front brake pads without removing calipers?

I read somewhere to turn old pad sideways and lever against the disc using it. I've tried this but it's still really hard going, the pistons are really tight.

I have removed the brake fluid reservoir top too.

Any tips on how to do this easier? Do I need a special tool?

The car is an R34 GTT with the standard Sumitomo calipers.

Trex Grand Master

Trex

Posted
Posted

quick search and i found this, not sure how well it would work.

corvette-brakes-17.jpg

I've had my pads out about 4 times in the last 2 weeks (because of squealing issues) i can't see any other way except for taking the caliper off, or possibly using that tool if it works well.

Also very interested if there is an easier way.

  • Like 1
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

quick search and i found this, not sure how well it would work.

corvette-brakes-17.jpg

I've had my pads out about 4 times in the last 2 weeks (because of squealing issues) i can't see any other way except for taking the caliper off, or possibly using that tool if it works well.

Also very interested if there is an easier way.

Thanks mate! What's the best way to compress the pistons with the caliper off, without a tool like that?

That tool does actually make sense if it's big enough - pull pads out on both sides and push opposing pistons in using the tool.

The other typical issue is the other piston popping up when you compress the other on the same side, so ideally you'd have two of these tools...

admS15 Grand Master

admS15

Posted
Posted

Thanks mate! What's the best way to compress the pistons with the caliper off, without a tool like that?

That tool does actually make sense if it's big enough - pull pads out on both sides and push opposing pistons in using the tool.

The other typical issue is the other piston popping up when you compress the other on the same side, so ideally you'd have two of these tools...

G clamp. Leave 1 pad in and use clamp to compress 2 pistons, then put the pad on the 2 pistons in the other side of caliper and repeat. Done.
hardsteppa Grand Master

hardsteppa

Posted
Posted (edited)

Use the ring end of a spanner bigger than the ID of the piston, say 19mm? Lever it carefully against the rotor with the ring end resting inside the piston and will push it in without issue, i have found.

Edited by hardsteppa
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

Thanks guys, looks like a combination of old pads, flat steel, spanners etc did it. Would have been quicker to just take the calipers off :)

I have ordered the tool Trex posted above to see if it saves some hassle next time.

V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

Thats is seriously a waste of money, a screwdriver or spanner is all ive ever used on all cars

Hehe yeah it's pretty basic ... however if it saves me an hour next time it'll be worth the $25 :)

75coupe Grand Master

75coupe

Posted
Posted

Youll get better at it the more you do it, its a 30min job changing the front pads now for me, no special tools required...

I find those types of tools just give chance to your caliper paint getting scratched and another tool to grab for the job...

  • Like 1
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

Youll get better at it the more you do it, its a 30min job changing the front pads now for me, no special tools required...

I find those types of tools just give chance to your caliper paint getting scratched and another tool to grab for the job...

I reckon that tool will take longer than a screw driver

Ok ppl with your fancy screwdrivers, do you just lever off the disc to push the pistons in? Or chuck something in between?

75coupe Grand Master

75coupe

Posted
Posted

Use a lever under the old pad to push the pistons back. Pull out one pad so you have some room, it will allow the rotor to have small amount of movement as well

dermy Collaborator

dermy

Posted
Posted

https://www.gettoolsdirect.com.au/kincrome-4-in-1-brake-pad-spreader-k8165.html?gdftrk=gdfV26854_a_7c442_a_7c1200_a_7c93871&gclid=CKX8qaP2ossCFQx9vQodP0AHJA

You could use this and not have to remove the caliper. But like everyones said i just lever with e screw driver

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      I’m thinking that’s the route I’ll  go, thanks for the input!
    • carnoobb
      V35 Overheat + Coolant Boil & Overflow + Engine not Starting

      By carnoobb · Posted

      Hey all, my 2004 Nissan Skyline 350GT overheated the other day with coolant boiling and leaking out of the coolant reservoir when I was parking. So today, I started it up again just to see if it was a thermostat/head gasket issue. After about 20 mins of running, temps were normal again, no coolant was leaking out and the upper reservoir hose was warm but my engine suddenly cut off. I checked the oil dipstick and cap when it was running and there was no white foamy residue and the exhaust did not have white smoke. I tried starting up the car again but it would only crank, similar to when I had a camshaft sensor issue just that now there’s no check engine light on the dash. Any ideas? Unfortunately I don’t have an OBD2 that can read the Nissan's programme.
    • Papichulo96
      Rb head oil drain dimensions

      By Papichulo96 · Posted

      Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • GTSBoy
      Need AC Compressor for R32

      By GTSBoy · Posted

      The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
×
×
  • Create New...