Jump to content
SAU Community

2016 Round 3 - Monday 14th March (labour Day) Hosted By Tampered Motorsport

acsplit

By acsplit,
in Archived Events

 Share

Recommended Posts

Kinkstaah Grand Master

Kinkstaah

Posted
Posted

Driver training?

Didn't know that was even a thing. Just saw the event and the car sort of semi-works so decided to bite the bullet, go slow and have fun!

As for the days, most of the negative reviews seemed to be from a few years ago, but thought people posting here may have more up to date information if there's anything terrible to look out for.

Link to comment
Share on other sites
billywhiz Proficient

billywhiz

Posted
Posted

There are often Driver Training groups on the days we participate in where you can be un-timed and have someone sit in with you to show you the lines/braking points etc.

Tampered are a little bit different, you can select Novice/Beginner etc but they allow passengers to run in all cars but you have to pay $20 for the privilege - I don't know if our club has a special deal agreed with Tampered to cover off driver instruction, Andrew?

Link to comment
Share on other sites
srs14t Explorer

srs14t

Posted
Posted

Track was a bit grippier, starting to rip apart in some areas though.

I was talking to one of the scruitineers, apparently they are going to have to resurface it again!

Otherwise it was a great day, apart from the large amount of cars there!!

  • Like 1
Link to comment
Share on other sites
admS15 Grand Master

admS15

Posted
Posted

Heaps of cars, sounds like a typical tampered day. I've only done a couple myself but found they still tend to run quite smoothly for the amount of cars they get. So surface coming apart, dodgy rush job then?

Link to comment
Share on other sites
srs14t Explorer

srs14t

Posted
Posted

The sessions were ran ok, but we were waiting over an hour and a half at some points till we were on track again!

Must be, though for around 3 million you would expect better, hey?

Link to comment
Share on other sites
 Share
Go to topic listing


  • Latest Posts

    • pogman
      George's R33 GTST build

      By pogman · Posted

      Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • GTSBoy
      Hello Everyone

      By GTSBoy · Posted

      They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • Triple OG
      Hello Everyone

      By Triple OG · Posted

      I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • r32-25t
      GReddy Injector Help!

      By r32-25t · Posted

      Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...