Jump to content
SAU Community

R33 With Haltech Idle/temp/voltage Problems

abr33

By abr33,
in Engines & Forced Induction

 Share

Recommended Posts

abr33 Proficient

abr33

Posted
Posted

Hi all, been a while since iv posted here.

In a nutshell im running a haltech e11v2 piggybacked onto the stock ecu (was to run auto) and basically something is giving noise to the ecu via the temp sensor, it can vary up to 30 degrees cycling as often as every half second or so. This causes big idle problems from shutting off to blowing smoke etc. Iv tried running both the wires separately (not both at the same time) to the ecu and the noise is still there.

Iv not been able to find anything out there with anyone having the same problem. Iv also tried a different sensor. The feed is getting 4.88V and the other is shared ground with the tps. That of which also gives me problems time to time. The noise is only there whilst engine is going and its not relative fluctuations to RPM.

Any pointers would be appreciated! cheers.

t_revz Grand Master

t_revz

Posted
Posted

Hey mate, have no idea about your exact problem but I do similar work on large mining gear.

Does the feed stay stable when unplugged and engine running? Checking across the pins and also feed to ground, are there any fluctuations. With it unplugged does the ecu show a fault or just a random number (ie -30)

Does it fault at all temps or only cold/hot?

abr33 Proficient

abr33

Posted
  • Author
Posted

Thanks for the reply,

the feed is stable with ignition but not whilst engine is running. Hot and cold doesnt matter basically the same thing. Only its worse under 70 degrees because its fluctuating cold start curcuit.

I cant disconnect it as its resistance based, if I unplug it it goes to -60 or something, which instantly kills the engine. Im going to try earth the sensor to battery but not sure if that will work.

t_revz Grand Master

t_revz

Posted
Posted

Id kick off the alternator belt next incase it's done a diode and has a slightly erratic voltage output. And double check ecu voltage for stability.

Have you done any recent welding on the car?

abr33 Proficient

abr33

Posted
  • Author
Posted

Id kick off the alternator belt next incase it's done a diode and has a slightly erratic voltage output. And double check ecu voltage for stability.

Have you done any recent welding on the car?

Probe the TPS to see if it is doing bullshit to the voltage on the common earth?

I have swapped the alternator to one with half the kms, and no welding for a long time before this began. It literally happened after being parked for 5 days.

I have run wires directly from ecu to sensor to no resolve. Im thinking of going straight from the ground on the sensor to the negative terminal on battery to rule out poor earth feed?

An GTSBoy, the tps is also brand new haha originally it was my only issue. Itd just lose the zero setting and try to idle out of the base map

abr33 Proficient

abr33

Posted
  • Author
Posted

Maybe give main chassis earths a clean too, I'd check from batt neg to sensor neg and see if it's 0v. If so I can't see it hurting earthing out the sensor to check

Yeah iv checked it all, and made a big 35 square cable for engine earth too

Does the problem change with tps disconnected? Same pulsing?

I cant unplug it or it dies lol. needs the reading to go into zero throttle idle map.

Ill have a play later in the week when I get a chance lol

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...