Jump to content
SAU Community

Largest Brakes Under R34 Gtt Stock 17" Wheels?


Recommended Posts

Sure let us know.

Rob and I did a trial fit of the GTT stock wheel tonight (with lug nuts acting as ~20mm spacers) and can confirm that it will NOT clear over the AOR 350mm kit.

It's not far off but enough to make a 343mm setup very much touch-and-go too - I think it will come down to the shape of the caliper really.

Thanks heaps Rob for your help on this!

Ps. With the wheel nut torque 100-110Nm should be a good range based on my research (e.g. http://www.skylineowners.com/forum/26-wheels-suspension-tyres-brakes/21254-wheel-nut-torque.html )

Link to comment
Share on other sites

I had a feeling 330mm is about as large as you can get under a generous 17". Subaru STi brakes are 326mm from memory and live under 17" wheels.

Yeah 330 is probably the target unless 343 can be squeezed on.

Not keen on 324/326 as it's a tiny increase over the stock 310mm..

Link to comment
Share on other sites

just get better pads, and ducting

Yeah I'm actually happy with the current brake setup in general, it's just that my pistons are starting to seize and I'm pretty sure rebuild won't be cheap. Hence looking at options to potentially upsize.

Keen on ducting too :) Have you got some for yours?

Link to comment
Share on other sites

Yeah I'm actually happy with the current brake setup in general, it's just that my pistons are starting to seize and I'm pretty sure rebuild won't be cheap. Hence looking at options to potentially upsize.

Keen on ducting too :) Have you got some for yours?

I'm planning to get these.. basic and "should" improve cooling as per my broscience hypothesis lol

ftpsize.JPG

  • Like 1
Link to comment
Share on other sites

Are they metal? Look like an unnecessary load of unsprung weight if they are. If they're CF, then fine. If it were me coming up with that idea (which I kind of like by the way), I'd knock them up in corflute. Nice and light and easy to repair/replace when you scone something hard on the road.

Link to comment
Share on other sites

yeah they are... doubt they weigh more than 500g a side? I know weight is weight and you're just adding more to the reciprocating mass but in the scheme of things..just get better wheels? LOL

https://conceptzperformance.com/czp-racing-performance-brake-cooling-duct-kit-nissan-300zx-90-96-z32-czp-brkdct-z32_p_7717.php

Link to comment
Share on other sites

  • 2 weeks later...

Jumping back to brakes for a moment, does anyone know if there's any chance of adapting HVS/AP Racing calipers onto Skyline hubs?

They're cheap as chips, a full 4-pot all-round kit with 365mm front and 350mm rear rotors for $2,799?! http://www.vsport.com.au/hsv-ve-vf-commodore-front-4-piston-365mm-rear-4-piston-350mm-brake-kit-2282

I ran a slightly smaller AP Racing kit on my old Monaro and it was fab.

Link to comment
Share on other sites

Adaptor would be difficult as commodore brake mounting points are a long way from outer edge of disc, if that makes sense. Normally an adaptor would move the Mount holes outwards, away from hub. I think in the case of putting commodore calipers it would be the opposite, and could get weird.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...