Jump to content
SAU Community

Recommended Posts

It's been a year or probably even longer since I put on QFM brakepads. I did not get the rotors machined as everyone I've showed them to, said they were fine and did not need it.

The problem since going onto QFMs has been the dust AND the noise. They squeel so much. I've taken the pads off and re-applied that special blue brakepad grease stuff at least 3 times now. It fixes things for a few days, then it goes back to total crapness.

What have I done wrong? I just replaced the rotors and brakepads on a family members Pulsar. No shims, no grease, nothing. And the car is silent as can be. It was just the cheapest pads and rotors they had at Bursons.

Should I have machined the rotors? Should I go get them done anyway since there is a local place that will do them for $15 each if I take them off the car and drop them in.

My previous pads were Nissan Hitachis and were silent with nowhere near as much brake dust.

Am annoyed I've not been able to solve this :(

Sounds to be the brakes pads are either the wrong size or not properly installed THEN you also need to check if your Pistons are hooked up properly. I had the same problem turned out they used aftermarket brake pads and it was the wrong size so kept making that squeaky sound.

To address the actual problem.....if you did not machine the rotors (and I agree it is not always necessary) then it is definitely one of the things you could/should try. Get a nice fresh surface without the old pads' binder material baked into/onto the cast iron. You'll want to scuff the new (but used) pads on a smoothish concrete surface to deglaze them and knock off any hard spots.

While you're working down there, check the runout on the wheel bearings, make sure there's not any movement in places that there's not supposed to be (like the caliper mounts), make sure th brake pad slider pins are clean and smooth, etc etc etc.

  • Like 1

Street car? Remsa pads, fkn awesome and cheap as broooo.

Bro you helped me install the QFMs when I bought your KYBs and Hardrace castor rods a couple of years ago. Yes it's just a daily driver.

The QFMs still suck. Yes I could just go ahead and replace them, but want to get my moneys worth out of these QFMs unless there is a market for second hand ones. I can't comprehand just how bad they are. The car stops on a dime, but I pay for it in squeel and dust. And that's why I picked QFM in the first place after reading reviews on dust from other brands. How much did you pay for Remsas?

I just recently bought some Protex I think it was pads and discs from Bursons for a family members Pulsar. No shims, no grease nothing. Just used a metal brush and cleaned the hub and installed them. Silent! Pads were only $39 for set.

If I go machine the rotors then maybe I should just get a new set of pads I don't know. But then I fear doing all this and they still squeel. That would suck.

Mine squeal horrendously when coming to a slow stop with remsa / roadhouse pads, They get worse the hotter they get. Using t3 rotors, braided lines etc.

I've tried bedding in - this makes it worse,

crc copper grease,

brand new shims with oem grease,

roughing up the pad,

cleaning the disc,

sanding the disc with 1k paper

I'm at that point where i am going to buy bendix pads. Trouble is that i will be left with remsa that are barely used and were bought because they're a crossover pad.

Mine squeal horrendously when coming to a slow stop with remsa / roadhouse pads, They get worse the hotter they get. Using t3 rotors, braided lines etc.

I've tried bedding in - this makes it worse,

crc copper grease,

brand new shims with oem grease,

roughing up the pad,

cleaning the disc,

sanding the disc with 1k paper

I'm at that point where i am going to buy bendix pads. Trouble is that i will be left with remsa that are barely used and were bought because they're a crossover pad.

I'm onto my third set of Remsas now, also with T3 rotors, HEL braided lines etc. Stock R34 GTT calipers, never had any issues with noise, off or on the track. Strange.

I've also just pulled my anti squeal half shims out to try to address unever pad wear, was fearing for the worst re noise, nothing.

I had the rear tyres replaced today. My rear rotors look to need machining. Is it worth trying to use the old pads? They are about half used, or just chuck them and start fresh with the machined rotors? I won't go hungry if you guys say yes, but it just means more money I cannot spend on the respray and then nistune/turbo replacements.

no pads will cause squealing; no manufacturer put a compound together, glued them to a backing plate, stuck them in a car for a test, heard them squeal like a pig and said "great, let's get them on the shelves". And I mean up to and including sprint or endurance race pads.

Yes some more agressive pads are more likely to be noisey but it is always a problem with the car and/or installation.

Squeal is a high frequency vibration in something that shouldn't be moving. Like GTSboy said above machining rotors and pads may help if they aren't new (flat), any moving parts like sliding pins, caliper pistons, touch point between pistons and pads (which should be anti squeal shims), hub to disc mounting surface, caliper bolts tight. By far the most common cause is simply brake dust, so get everything nice and clean when you reassemble.

If the noise goes away when you add anti squeal goop between the piston and pad that tells you the problem is likely in that contact somewhere. So clean and check the shims are not bent etc

Intima SR for street car

Wow 700C temp rating, higher than the A1RM. How do the SR go on the track?

My Intima SS's died on the hills, need some convincing to go back to Intima after that..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
    • Yup but for me its the HR ! Cut my teeth on the old holden 6s in the day ! And here's me thinking in the day it was also the 300ZX and the Mitsubishi GT3000 ! All, as well had good lines, but always seemed to need finishing off, style wise.
×
×
  • Create New...