Jump to content
SAU Community

Recommended Posts

Hey guys

I want to replace my engine oil in my R34 (RB25DET Neo). I've done some research on the best oils. Everyone has their own opinion on oils but the majority seems to be leaning towards the Motul Turbolight 4100 engine oil. So I went to a couple of stores to check if any has them in stock but na-da, nothing. Autobarn has 2 Motul oils which are 6100 synergie and 8100 x-cess. I asked one of the clerks at the store and he said that I should try Auto Pro, so I rang two Auto Pro stores and they both told me that Motul has stopped producing turbolights and that Motul has replaced it with Motul H-Tech 100 Plus. Is this true?

Has anyone tried Motul H-Tech 100+? Is it really the replacement of turbolight and is it the same or better?

Also, a store here in Perth has Motul 300V Chrono in stock which apparently is some high quality shit for if you're going to the races or something but it's $110 for 4L! And I only use my R34 as a streetcar and daily drives. I'm not planning on racing with it or going sideways. Will the 300V be worth it as a streetcar?

Also, now that winter is starting should I look at buying a lower viscosity oil?

What do you guys reckon?

Edited by Joni Boi

300v is awesome, made my car noticeably faster. No joke. Not wallet friendly though.

I used to use 4100 religiously and it's a good oil but yes, you can get equal/better oils for same price and it pissed me off that it was so hard to find, so ended up switching oils to something most stores stock.

300v is awesome, made my car noticeably faster. No joke. Not wallet friendly though.

I used to use 4100 religiously and it's a good oil but yes, you can get equal/better oils for same price and it pissed me off that it was so hard to find, so ended up switching oils to something most stores stock.

Oh ok, I thought turbolight was good for your turbo or something lolz, I don't know much about engine oils. But I'll try get something full synthetic 10w-40 like junkie said

Nulon Hi-Tech 10W-40 or Penrite HPR10 will be fine. Grab a few when they are on special at Supercheap. I have 4x bottles of HPR10 in the carhole

Cheers mate :) I'll do that tomorrow.

Anyone els want to voice their suggestions, I'm still open for anything els to try

for me, Castrol edge seemed to hold temp and oil pressure better, I noticed oil temp went up when I switched to the penrite 10-tenths. Will likely go back to the Castrol at next oil change, but would use penrite again if needed, and it is widely available.

I bought new oil, filter and sump + washer bolt (from nissan dealership). Came home, jacked the car up, went to go unbolt the sump and f**k me, the bloody thing is stripped...

200.gif

Now I've got a problem that I can't be bothered posting a new thread about so I'm gonna post here. It keeps turning anti-clock wise but it won't come out, not even a little bit. $@!$$@!!! Previous owner or mechanic must have over tightened it when they changed the oil. I really don't want to buy a new drain pan. This is so stupid! :rant: I tried getting a screw driver under the sump to lever it into a thread but cant get a gap between the sump and pan. Also tried loosening and at the same time pulling it with pliers but no dice.

GUYS, don't overtighten stuff!!

Edited by Joni Boi

I would assume the same as the coolant drain bolt: 34-44 Nm?

I just tighten it and when it starts getting tight, just nip it a little. Won't fall out lol. You can put thread sealant on the sump so it never leaks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You're not wrong, but more than a few times I've heard of people running into issues where their injector characterization isn't quite right and that approach works for that specific configuration but once they switch over to a new set they discover a whole bunch of stuff wasn't set up correctly. It's slightly more annoying to reverse engineer the OEM MAF transfer function but you already have the sensor wired up to the factory harness so keeping it around for a few weeks more while you figure out the tune is easy enough. I've seen GM also use a combination of both MAF + MAP in their ECUs before, MAF is for steady state and a calculation of the cylinder VE to correct the base VE table, then in transients it uses that calculated VE + raw MAP to determine cylinder filling somehow.
    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
×
×
  • Create New...