Jump to content
SAU Community

Recommended Posts

Had a Haltec then a Motec M84 and went back to a PFC D-jetro.

The car has been running faultless ever since, no more timing issues and its a real plug in ecu.

Unless going a crank trigger I would stick with Nistune or PFC. They just work.

Put it this way.

I'd keep my car stock before a pfc again.

They are a complete waste of money. Nistune does everything it does.

And you may not want what a haltech does now, but if you do you have wasted time and money getting a half arsed ecu. May have well gone the good one from the start. Not to mention if you do get a power fc and take it to a well known tuner and they can't tune it that means more money down the drain. Let alone all the benefits a haltech brings.

I'll also point out the ecu is arguably the most important part of the car. What's an extra $1000 of you buy new? On the price of a motor it's well worth it.

Tl;dr pfc waste of money.

  • Like 1

Put it this way.

I'd keep my car stock before a pfc again.

They are a complete waste of money. Nistune does everything it does.

And you may not want what a haltech does now, but if you do you have wasted time and money getting a half arsed ecu. May have well gone the good one from the start. Not to mention if you do get a power fc and take it to a well known tuner and they can't tune it that means more money down the drain. Let alone all the benefits a haltech brings.

I'll also point out the ecu is arguably the most important part of the car. What's an extra $1000 of you buy new? On the price of a motor it's well worth it.

Tl;dr pfc waste of money.

I couldn't disagree with you anymore at this point. The higher power you go with Nistune, the worse the tune gets. O2 correction always trying to battle with the tune. I can name quite a few different people with GTRs that are considering swapping from Nistune over to PFC.

You want accurate timing with a Haltech, you kinda need a crank trigger, it jumps all over the shop without one. It's not "just an extra grand" for most people who haven't swung a spanner in their lives. PowerFC does the job, and it has been doing the job for the last 25+ years on THOUSANDS of high performance cars. You cannot possibly use confirmation bias just because you had a junk tune, and trash the ECU which thousands of people have zero issues with.

  • Like 1

There was nothing wrong with my tune, bit ecu technology has come a long way. The pfc was good. It's just not worth the $$ they ask for now. And yes it is $1000 difference and I have the receipts to prove it. You don't need a crank trigger so all.

Point is, why half arsed do something that will end up costing you more down the line. Just get a decent ecu to begin with.

Because 50% of Gtr owners realise the hole they have dug themselves within a year of ownership and sell up and cut their losses. The other half bend over and open up their wallets anyway, spending a little more than a small fortune. :P

Edited by iruvyouskyrine

There was nothing wrong with my tune, bit ecu technology has come a long way. The pfc was good. It's just not worth the $$ they ask for now. And yes it is $1000 difference and I have the receipts to prove it. You don't need a crank trigger so all.

Point is, why half arsed do something that will end up costing you more down the line. Just get a decent ecu to begin with.

You can get them secondhand for $400 if you wait long enough, average price is $600 for a GTR PFC. How is it half arsing? It'll go with your mods all the way up to 450kw very comfortably.. even more if you go D-Jetro..

You don't need a crank trigger so all.

Its a known issue that they have difficulty reading the cas signal which is hit and miss, just call haltec or Motec and they will clarify your error.

Point is, why half arsed do something that will end up costing you more down the line. Just get a decent ecu to begin with.

Where is a nistune or PFC half arsed? You just don't get the wank factor bells and whistles that you really don't need in a street car if the tuner knows what he is doing.

The only real choice to make is to stick with the AFM or go MAP. Apart from that Nistune or PFC will manage a 400kw+ car easily and perfectly.

Edited by XGTRX

You can get them secondhand for $400 if you wait long enough, average price is $600 for a GTR PFC. How is it half arsing? It'll go with your mods all the way up to 450kw very comfortably.. even more if you go D-Jetro..

dont go second hand.

The ecu and tune is the most important part of the build.

  • Like 1

If you've built a 400kw car you have obviously spent abit of money so why would you skimp on the thing that is going to keep your car running right.

Buy the best computer your budget will allow and make sure you get it tuned by someone with the correct knowledge to tune it correctly

  • Like 2

fyp. Have you never spoken to anyone who has bought a stuffed second hand ecu?

This isn't a missile car, this is a 400+kw R. Choose parts wisely and don't cut corners.

Yes and I've had a hand in building many of those cars. I could confidently say less than 10% of those who have gone second hand, have had problems, I'm talking 40+ cars here as well.

So 90% have had problems?

I rest my case.

Okay mate, I edited my post before you posted that but if you want to be childish thats fine.

Anfanee, what exactly is a platinum pro going to do over a PFC that your average joe shmo actually NEEDS? Go on GTR PARTS on Facebook and you can pickup a PFC D-Jetro any day of the week for $700. I don't see what the issue is here?

My point is. It's a much better ecu. And it's future proof. If you end up deciding you want the extra features that $500 tune may have well gone a haltech from the start.

Also AFM are shit.

You're right on all those parts you just said, I just don't think the average person needs it, 400kw isn't even anything fancy nowadays in the GTR world. Every third GTR in Sydney seems to be minimum 350-400kw. You buy an ECU to suit your application and in most cases a PFC is going to more than cut it.

On top of that... you should be listening to your tuner anyway. If he tells you he prefers to tune Haltech or PFC, then you should definitely be listening up!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...