Jump to content
SAU Community

Recommended Posts

Hey guys I've just bought myself a 98 R34 GTT. Not I found a few little problems with the car but nothing major. The one thing that's got me is the TCS system doesn't seem to work at all???

I've checked the boot for and mods to the ECU , checked the plug and it's plugged in. I'm just lost at what next. The car breaks traction all the time and I have no slip light at all on the dash board. Not even with ign on

All the plugs are plugged up to the butterfly near the TB.

Please any ideas would be greatly appreciated.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/464566-r34-gtt-no-tcs/
Share on other sites

The traction control system sucks hard, and just slams the throttle shut. Disabling it is a smart thing to do.

Making it work again is a waste of time.

Get better tyres, drive better.

How much power is it making?

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/464566-r34-gtt-no-tcs/#findComment-7720929
Share on other sites

Hey guys I've just bought myself a 98 R34 GTT. Not I found a few little problems with the car but nothing major. The one thing that's got me is the TCS system doesn't seem to work at all???

I've checked the boot for and mods to the ECU , checked the plug and it's plugged in. I'm just lost at what next. The car breaks traction all the time and I have no slip light at all on the dash board. Not even with ign on

All the plugs are plugged up to the butterfly near the TB.

Please any ideas would be greatly appreciated.

Cheers

Please check your ECU fault codes and report back. Instructions here, scroll down for a pic of which pins to short: http://www.sau.com.au/forums/topic/266512-reading-nissan-fault-codes-ecu-fault-codes-how-read-them/

I'm currently getting Code 17: ABS-TCS C/U Signal. My TCS never worked since the manual conversion but the ABS is fine.

TCS and SLIP lights are on in the dash too, along with A/T and HICAS because they no longer exist...

Should also state that all it really does is put a 2nd throttle to 60% max throttle. I was able to break traction pretty easily with stock power with the traction control on

Fresh avatar Greg? And yes you're right it's not the most sophisticated system is it...

Link to comment
https://www.sau.com.au/forums/topic/464566-r34-gtt-no-tcs/#findComment-7721294
Share on other sites

No. Fault codes are read from the dash light. I don't know what light they use in a 34 - it could be a dedicated CEL. I have my Neo in an R32 so I have the cat light as the CEL.

The best way to read the codes is to use a Consult scanner plugged into the Consult port. More to the point.....the best way to read codes on any of the control units in the car is through the Consult port. If you have a buggered sensor (say the steering angle sensor) then you cannot execute the routine required to put the HICAS CU into diagnostic mode. So you can't find out that you've got a buggered sensor. See the fault in Nissan's logic with the silly dances you have to do to enter diag modes? Scanners cut right through that crap.

Resetting the ECU is a simple case of leaving it without power for a while.

A lot of people actually remove dashbulbs to mask hardware faults that bring up the lights. ABS/TCS, being as optional as they are, would be the biggest candidates.

Link to comment
https://www.sau.com.au/forums/topic/464566-r34-gtt-no-tcs/#findComment-7721756
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Does that price include the rack time to straighten the frame and body and replacement of parts and paint, as well as the noise and emmisions testing  The last engineering certificate I had done, albeit about 15 years ago, was around $1000 for a few inspections and the certificate 
    • 😂 thanks guys. The diagram i had did not have the breather on it at all. Much appreciated.  
    • Geez, engineers fees have definitely gone up. Mine back 2007 cost me all of $300. Mind you, I had to go back to him a few times to get him to write the correct things on the report after he'd inspected it. Things like wrong exhaust size, wrong wheel sizes, etc etc.
    • Can we see a scan of the original quote? The problem with engineers (and by this, I mean, all engineers across all engineering industries) is that there are "engineers" and there are "engineers" (you'll have to imagine the two different vocal emphases on those two versions of the same word. Engineering is a mindset - your farm kid who spent his life rebuilding the tractor will likely make a good engineer. The farm kid who spent his life taking photos of butterflies.. perhaps not. But on top of that mindset, the modern engineer has to learn how to write so that there is absolutely no way of being misunderstood. Proposals/budget estimates/quotations are one place where this is absolutely vital. You have to delineate your scope of supply with extremely hard boundaries, and anywhere where there is any possibility of not being able to have such a hard boundary, you need to write language that will cover you from scope creep, cost overruns, the inevitable interference of the client or their "engineer", etc etc. Now, if your clients are the BHPs and the Rio Tintos of the world, and similar, then you get good at this. If you are an automotive engineer, pitching work to the great unwashed masses, your skills in this area might not be well developed, because you're only dealing with knuckle draggers trying to get a big block legal in a Torana. And when I say "might not"....I'd suggest there's a better than even chance that any such skills might be completely absent. So, we might be able to look at your quote and see what the opportunities are for rebuttal.
×
×
  • Create New...