Jump to content
SAU Community

Half Shaft Spline Count On R32 Gtr's

mxdori
 Share

Recommended Posts

mxdori Apprentice

mxdori

Posted
Posted

I've tried looking, but would like to know what Spline the half shafts are that go into the diff centre for 1989 to 1992 GTR.

Reason being I've bought a drift specific ATS 2way. On the box says Suit BNR32, R34, S15. And spline count was 29.

From what I can research it will fit s15 helica, r34 gt rb25 or rb20 open diff, and bnr32 with mechanical 1989-till late 1992-early 93.

I would like to use the GTR diff because of the stronger 6x1 axles, but worried the spline on the half shafts are different!?

Thanks

Link to comment
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

R32 GTRs had 3 different spline counts. But it doesn't matter, because I think the actual diameter of the shafts is bigger than any of those other diffs. There are also various half shaft length differences between the many R200s. For example, you cannot use the same shafts in S15 helical as typical Skyline diffs, because one side is a different length between them.

Link to comment
Share on other sites
IT15ON Contributor

IT15ON

Posted
Posted

Hey mate not sure if this will help or not, i purchased a nismo gt pro to suit 32 gtr. Went to fit it to my viscous housing r200 (in s13) and couldn't get the center to fit in housing. I ended up buying a complete 32 gtr diff and am getting a shop to swap it all over. So next week i may be able to get it back and check the shafts etc for ya but as gtsboy said not sure if they'll match yours or not

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      Much less twat-tastic. CF wheels are too garish for civilised use.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...