Jump to content
SAU Community

[04/06/2016] Imports First Meet - Baldivis


Recommended Posts

Hey all, just got invited by a friend to the Imports First Meet in Baldivis. <- This is a link

All of the information I have is from the Facebook page, so check that if there are any changes.

When: Saturday the Fourth of June (04/06/2016) at 20:00-14:00 (That's Eight O'Clock in the Evening until Two O'Clock in the Morning.)

Where: Baldivis Masters, Corner Safety Bay Rd & Baldivis Road, Baldivis WA, 6107

Who: Will Add names here after confirmation

Pre-Meet Location: [to be confirmed]

These are the same guys who organised the Joondalup meet from last Saturday.

Important Information:

There is a No-Hoon Policy, Imports First have stated on the facebook page:

Whose keen for this weekend?

But also saying that, anyone that does excessive revving, skids or burnouts number plates will be taken so don't ruin it for everyone else as that behavior will not be tolerated and further action may be taken so everyone drive save and we will see you all on the weekend.

There is Discussion of a Cruise down to the Rockingham Foreshore after the Meet, but I don't know if that's official or not.

Also, for anyone with a lowered car, Enter from where the Main Masters sign is, as there's no speed-bumps, although it is a tight turn.

It's a pretty easy location to get to, if you're North of Rockingham, take the Freeway South and Exit at Safety Bay Road, Turn Right and Baldivis Masters will be on the Left, just after the Giant Round-A-Bout where the Caltex Fuel Station is (great if you need a top up after the drive)

The Instructions are pretty much the same for those South of Rockingham - Get on the freeway, Exit at Safety Bay Road and Turn Left, it's right next to the freeway.

There's a Hungry Jacks and a Subway there as well for any one hungry and brave.

If you're in the Mandurah area you probably know how to get there, but if not - Get on Ennis Avenue, Exit onto Old Mandurah Road, follow through to Eighty Road, It will be on your Left..

Right, with that being said, let me know if you're going and I will add your names to this post.

Also, if you want to organize a meet up before-hand, post it below and when we decide on a location I will add it to this post to. We only have Three days until the event, so please be hasty with your responses.

I don't need to say this but I will - Drive Safe, Do not Drive Tired, Do not "Show off", Let's get there safely, in one piece and enjoy the drive also: Theres usually speed cameras southbound on the freeway, I make that trip a lot, don't be stupid.

Thank you.

  • Like 1

It's miles away from me , so I'll give it a miss on this one :) Dave and I going for drink and nibbles with WRX's cruise tonight , come and join at Hillarys if any of you want to join and say hello [emoji28]

Edited by ElleAli76

The way I see it is:

Double Demerits + Baldivis is a bit of a recipe for disaster, I made this thread though, just to raise awareness of it, if any one did want to go.

Sorry to all my Rockingham/Mandurah/Baldivis friends (I grew up down there), but it is what it is.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
    • I've got three stashed away but it's starting to get silly with the prices 
×
×
  • Create New...