Jump to content
SAU Community

Recommended Posts

Hello everyone I'm Paul from the uk.

Been the proud owner of an r33 gtst spec 2 auto in sonic silver for 2.5 years now and i've been looking at upping power.

Went to santa pod raceway this weekend to see what the car would do with some like minded owners sadly things didn't go to plan so to cut a long story short I was on my way home and suddenly lost drive, blipped it and the revs jumped up but the car didn't respond and just carried on doing the same speed. I coasted around 100M to where I could pull off the road, as I did I could smell burning :(

Jumped out to find ATF down the side of the car and a split hose from my oil cooler, it was still running out.

Managed to organise some ATF and bodge the hose by bypassing the cooler, drove home with tail between legs and took it very easy.

My question is how much damage have i done? any? none? new box? the oil was still nice and red that was coming out but it did pong a bit. once topped up the box "seemed" fine but I didn't take her above 3k rpm.

I'm going to hazard a guess and say I should take it out, get it into third and give it some therapy and see if it slips at all.

Any other suggestions to tell?

I'm truly gutted.

 

 

Link to comment
Share on other sites

Yea I just took it nice and easy all the way, box seemed fine but I can't help but worry about it, push comes to shove I'll have to get another box beauty of that is nobody wants auto boxes so they're dead cheap. There was a couple on eBay one for £25 and another for £45 where as the manual boxes go for between £500 and £700 !!

I'm relocating the oil cooler tonight to a more suitable position, then I'll get her out and see, fingers crossed......

Link to comment
Share on other sites

Right, pulled my tranny cooler set up to pieces today and and repositioned it all.

Just topping up the fluid and looking for answers on the net but there's nothing definite so...

do I check the level with the engine idling cold? Or hot?

or

do I check the level with the engine off cold? Or hot?

or all four?? Lol

Sorry there's not many auto owners over here in the uk.

Thanks guys.

Link to comment
Share on other sites

When the line popped I topped up with 3 litres, the trans came back to life, well it got me home driving gently. The fluid was around 20 miles old no more than that. Topped back up yesterday and tried the dipstick when it was warm and idling it was low, barely registering in fact, turned engine off waited five minutes for it to settle and it measuresd perfect for  a hot engine.

So it's a bit confusing, really want to get this sorted so I can take the car out and see if the box is damaged after what happened.

thanks for everyone's input on this, much appreciated.

Link to comment
Share on other sites

So I put another almost two litres in today bit by bit, box seems fine, got it up to temperature and gave it some beans, didn't slip and it's still going.

 

Thanks for everyone's help :0)

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...