Jump to content
SAU Community

Recommended Posts

On my way home from work this afternoon. Stopped at an unbroken white line, waiting for a gap to turn left.

A second or two later I'm rocked by a solid hit from behind courtesy of an inattentive driver in a late model 5 door Nissan Patrol.

Rounded the corner & pulled into a driveway to exchange details and this is the damage done.

C-pillar and roof-line don't have any discernible creases or dents, and as far as I can tell the floor-pan is fine.

Boot-lid closes and latches, but with a decent gap on the drivers side and a crease on the underside where the boot surround has peaked above the tail-light.

Tail, brake & indicator lights all functioning, still roadworthy.

I've put a lot of time and effort into this car and am considerably upset by this, what do you guys think? Repairable or write-off?

The Chameleon paint was laid on the June long-weekend, hadn't even finished cutting & buffing it.

 

 

 

 

 

IMG_20160713_153753.jpg

IMG_20160713_165349.jpg

IMG_20160713_165359.jpg

Edited by IpoopThere4Iam
Link to comment
https://www.sau.com.au/forums/topic/465780-r32-gts-shunted-write-off/
Share on other sites

On 14/07/2016 at 9:50 AM, jmknights93 said:

Far out! I don't suppose this was around our area was it?

Wetherill park, about 1K south of the reservoir. I haven't installed those injectors yet, but they look immaculate. Depending on the outcome, they may end up in another r32.

 

On 14/07/2016 at 10:12 AM, admS15 said:

Hard to see much from those pics but from what I can see it does look repairable. Why dont you swing it past a panel shop and see what they say.

2 quotes so far, both between $3-4k. Have to plod through the whole insurance process now, will keep u guys updated.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Cut sump up and extend. Win win 😂 
    • All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • also, we need to know which solution worked....
×
×
  • Create New...