Jump to content
SAU Community

AC condensor fan

yoshiii335

By yoshiii335,
in General Maintenance

 Share

Recommended Posts

Duncan Grand Master

Duncan

Posted
Posted
5 hours ago, admS15 said:

 

5 hours ago, admS15 said:

Hello,

Its not meant to. It is overheat fan.

Good bye.

 

5 hours ago, admS15 said:

Google would have said the same. Bye.

Why the rudeness? If it's too far below you to answer a question without the sarcasm, then don't....

Duncan Grand Master

Duncan

Posted
Posted

Oh BTW, I googled the question and didn't get this answer.

Well actually I did because this thread exists but I didn't see the answer elsewhere in the first few pages.

People should feel able to ask questions here, it's why the forum exists.

admS15 Grand Master

admS15

Posted
Posted
Oh BTW, I googled the question and didn't get this answer.

Well actually I did because this thread exists but I didn't see the answer elsewhere in the first few pages.

People should feel able to ask questions here, it's why the forum exists.




That's odd because it was the first thing that came up when I googled. Hence I was able to provide the answer to the op's question albeit sarcastically.
Shoota_77 Veteran

Shoota_77

Posted
Posted

I agree with Duncan, let's lay off the sarcasm. Forums are about helping each other, not making them too embarrassed to ask what to some is an obvious question, to others is not....

If he's clearly asked the same question before and been given the same answer then yes I agree, it can be a little annoying. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Hr34 fuel pump not turning on

      By Duncan · Posted

      If you get 12v at one of the relay pins with IGN on, and 12v at another for about 3 sec when you turn the key from ACC to start, then yes you can just earth the relay trigger pin. Just have a look at the top of the relay, it should tell you which pin needs earth when the 12v signal is sent (or if it's not clear, just post the pic and we can work it out). If you always have 12v at 2 pins with IGN on, they it is earth triggered by the ECU which makes it harder to fix (you really need to check the ECU pin is earthing when it should, and if so it is a wiring issue from there to the relay.
    • Duncan
      Tomei gasket

      By Duncan · Posted

      Tomei make a 1.5mm restrictor, I'd just use that.
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the gearbox in and the front drive shafts.
    • rahilp
      Requirements for Xenon Headlights? (Possible Solution)

      By rahilp · Posted

      Hi There I went through a rabbit hole of reading about Xenon headlights and the ADR regulations for having them installed. As people have been defected by running factory xenon I was researching in ways to make them compliant. Everyone always say needs to be self leveling and have washer installed, which I don't necessarily agree with. For this argument I'm using R34 as reference as I'm more aware on the construction of the headlight compared to the R33 Xenon, which may still be the exact same case.   For the self leveling clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles As you can see the bold text "these manually adjustable devices from driver seats" are fine to use. As Series 1 Xenon model headlights do have a 4 level adjuster on the right near the ignition (however not series 2) then these model are consider compliant in that argument.   For the Self Cleaning aspect of this argument clause taken from ADR 13 - Installation of Lighting and Light Signalling Devices on other than L-Group Vehicles Now i can understand the argument that Xenon will need a washer as they are over 2000 lumens, but I clicked on the 12 at the end of that sentence and it takes me to the end notes which states R34 for headlight lenses are plastic, not sure if PL is mark as I don't currently have my skyline to confirm that marking is there. But could you not technically get a lenses with the PL marking on it and then get away with the argument that you need a washer. I went through a quick read of the adr and might have missed something else that may cause them to be non-complaint.    But wouldn't these technically be complaint headlights   Would love to hear other people input on this and shed some light   Edit In regard to the the washer portion I might be mistaken ADR 45 (which I believe is Regulation NO.45) states 12 cd (candela) I dont understand that portion in regarding to calculating the candela if anyone can shed some light. Otherwise I guess throw in a washer for the headlight and you definitely comply.
    • r32-25t
      R32 Gtr Long Term Love, Now Project

      By r32-25t · Posted

      Took it to all Japan day, flogged the hell out of it and took it all, am a very very happy man  don’t know how that ended up in Greg’s thread before
×
×
  • Create New...