Jump to content
SAU Community

Recommended Posts

Tryed searching through past topics nothing really the same problem as mine

Anyway everytime i turn my car on from a cold start it turns over about 3 to 4 times makes a weird noise like its got no power then once it fires it up it idles at around 500rpm and i have to press the acceleartor

The weird thing is it makes a weird churp noise 2 or 3 times before it starts..

Is this my alternator which is gone? or battery...?

I also have a remote start and it doesnt seem to work it just clicks and trys to ignite and just doesnt start lol

So what do u think?

Thanks in advance :D

Link to comment
https://www.sau.com.au/forums/topic/46611-starting-up/
Share on other sites

I am Currently Experiencing the same problems, So far no one has been able to figure out why our cars do this (Other people have been having the same problem on this forum)

Apparently this is a classic Sign of Dead Spark Plug(s).

Try Changing them.

This however was un sucessful for me.

02 Sensor - Could be your next check. However this maybe something out of Left field.

Fuel Pump - A dead or Dying Fuel Pump apparently has these symptoms.

Cold Start Sensor - Apparently this should ve investigated.

Air Flow Meter - Personally cant remember is this is the correct part mentioned, But cleaning out your Airfilter and Meter can have some improvements.

Please let me know how you go, Maybe try the above advice one day at a time, that way It will narrow down exactly what the problem is/was.

Im sure other people will be interested in hearing how you go.

Good Luck!

Thanks,

Essential.

Link to comment
https://www.sau.com.au/forums/topic/46611-starting-up/#findComment-946179
Share on other sites

I used to have this problem when i first got my car. It is a combination of a few factors. Firsty, when most cars come from japan, the battery dies, because it is not used for months.

The chirp and weak start is the battery. Get a booster pack and connect it up, and you'll notice the difference a stronger battery will make. No more chirp, and should start quicker.

Secondly, the low idle. For me, it was my car not adjusted properly to our shit aussie fuel. I ran a few tanks of our shit 98 octane fuel, then reset ecu. Problem went away. Rough idle can also be caused by other factors such as broken afm, idle may also be set too low.

Link to comment
https://www.sau.com.au/forums/topic/46611-starting-up/#findComment-946274
Share on other sites

When cranking a good battery should not drop below 10volts, when started you should have 14-14.5Volts back at the battery.

Starting a cold car is alot harder then starting a warm car, so if your starter is worn - she will struggle. Also once the car has been running for a while the battery will store a surface charge, That will give the starter more amps to deliver when cranking - so if starts easier. The surface charge disappears after 1-2hrs

Link to comment
https://www.sau.com.au/forums/topic/46611-starting-up/#findComment-946811
Share on other sites

I had a similar problem. Check the voltage when starting the car and it cranks, i found that mine dropped from 14V (indicating that it was charging ok, thus no alternator problems) to around 7V when the engine cranked. It was 90% due to the battery and i went and got myself a new one.

Starts great everytime now, even in the cold, after days of not driving it.

Gauth

Link to comment
https://www.sau.com.au/forums/topic/46611-starting-up/#findComment-952849
Share on other sites

. Check the voltage when starting the car and it cranks, i found that mine dropped from 14V (indicating that it was charging ok, thus no alternator problems) to around 7V when the engine cranked. Gauth

Mate, I dont wanna stomp on your pride, but how can an altenator be producing 14 volts before the engine is started?

Sumo

Link to comment
https://www.sau.com.au/forums/topic/46611-starting-up/#findComment-960686
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You shouldn't need to massively fatten up the mixtures for cold conditions. For one thing - 0°C is not that cold. For another, the Haltech will be using the IAT sensor to tell it how dense the air air, and calculate the correct amount of fuelling. Then the cold start enrichment is added as a % on top of that, so it should scale with the main fuelling. You might also doubt the IAT sensor at this time. You're not using one from an RB26 are you? Using a nice Bosch sensor or similar? Happens. Some wideband units take great pleasure in killing their sensors. Put another wideband in the tailpipe and compare. Or just swap the sensor to a brand new one and see.
    • Oh, my misunderstand. When the car was running, it sounded ok, but if I gave it any gas it wanted to die but caught itself afterwards. It's very different from how it was a couple months ago when it was warmer outside. The logs show that the AFRs are better during, what I assume, is warmup enrichment. Because it's cold, and air is more dense, should I work on the enrichment bit?
    • yess of course im not using 2nd hand parts from my spare engine, but the place where i live is hard to find parts for the RB20DET ,but for the RB20E is everywhere including new ones and a lot cheaper ,because for the RB20DET you have to order it overseas to get one and it cost a lot of money 3x the price to be exact. so i ask this topic because if i can use the new ones but for RB20E is it compatible or not. if not im screwed haha, not totally screwed but i have to save a lot of money first before i can begin repairing my engine, thanks for the information before.
    • Unless my sensor just died, was only a couple months old, I strongly believe it didn't. How can I test it? I never mentioned it being 20:1+?
    • Well, you wouldn't use 2nd hand bearings out of another engine anyway....so just buying the proper bearings is obviously what you're going to do. The crankshaft would be common. The conrods might be common. There is essentially nothing else you would be able to use.
×
×
  • Create New...