Jump to content
SAU Community

Low / Faint beeping Noise R33 S2

ADM33T
 Share

Recommended Posts

ADM33T Explorer

ADM33T

Posted
Posted

Hi All,

Hoping for some advice as I have lost hope after about 30mins lol

So the issue developed about 2 weeks ago when I moved it to wash.

Moving in / out the driveway and sitting idle I could hear a very low constant beep noise, at first I thought it was the turbo timer but nope it's def not that.

I have stuck my head all through out the dash around the drivers side, the best location is above the left knee around the steering column but I still can't locate it. It's a very low pitched beep and if you were sitting in the passenger seat you probably wouldn't hear it.

It also was not present prior to hearing it.

Any help is appreciated.

Link to comment
https://www.sau.com.au/forums/topic/466229-low-faint-beeping-noise-r33-s2/
Share on other sites
Sinista32 Grand Master

Sinista32

Posted
Posted

Check for a small speaker looking unit behind the drivers side door card

other thought was an aftermarket alarm with a dead/dying roll of watch batteries

perhaps even a hidden turbo timer behind the dash

  • Like 1
  • 2 weeks later...
Steve85 Mentor

Steve85

Posted
Posted

Depending on the sound it could be some sort of earthing issue. I know that one of my old cars made a low pitch whine when it was started. It varied with the RPM of the engine. 

One thing I can suggest is to double check your terminals on the battery (assuming you don't have two). Make sure they are super clean and tight. If your car has a separate earthing point to the chassis (normally located either at the front of the car or near the strut towers), check the earth. If this is in poor shape you can introduce all sorts of odd harmonics.

The other sound that it could be is a dying capacitor. They make a funny squealing sound when they are dying. Do you have any electronics (PCBs) mounted in the area that could be the source? 

Steve85 Mentor

Steve85

Posted
Posted

^^^ That said if you are absolutely sure this is a beep and not some spurious noise, you need to look for electronic boards. You will most likely be hearing a piezo speaker. These are generally smaller than a 5 cent piece and are mounted within electronics, so are hard to hear. 

Most smart (read: well designed) items will start to beep if the board detects a lack of power. 

Quote

dead/dying roll of watch batteries

This is most likely the reason, most of the circuit will be receiving 12V (or thereabouts) from the car and will operate fine, but the backup battery (normally a lithium watch or button battery) may run on a different area of the board with it's own power sense circuit. When the power drops the circuit will move from it's normal mode of operation, to a circuit that include the speaker, thereby creating the beep. 

I'm not familiar with enough of the R33 electronics or any of the aftermarket items to know what it could be, but you may find it's as silly as the clock or radio in the car.

I'd suggest (if it bothers you enough) to pull off any trim in the area and try to isolate the sound. It could be coming from deep within your dash.

ADM33T Explorer

ADM33T

Posted
  • Author
Posted

Yes that's the stumping part.

Only when the car is on it beeps.

It's comes from around the steering column.

I'm going to spend some more time on it as I noticed the greddy control boxes are shoved around in there ( I assume control boxes for boost and oil temp gauge ) I seem to have a sneaky suspicion it may be either of them cause that's the only items in the vicinity.

Also ripped out the turbo timer and still doing it.


  • 3 months later...
  • 7 months later...
  • 1 year later...
kool Newbie

kool

Posted
Posted (edited)

Any solution to this ? I have similar situation in my skyline V35, 3 beeps at ~1 every 2 sec interval even without keys inserted, lower than the sound it makes when I leave the keys in with door open. Does not make the beep sound when I have car running though. 

Edited by kool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Yet another clutch question

      By joshuaho96 · Posted

      It's excellent but I'm still breaking it in so I'm not 100% sure where it'll end up. I would say it's about 15% heavier than stock and the smoothness of the slip zone is quite progressive but you need to be a little patient compared to stock or it'll bite hard and stall. Stock I got away with absolutely horrid clutch control. Like I said before I couldn't even tell where the clutch would grab when it was stock so releasing way too quickly without enough revs it would just slip and the revs would drop lower than ideal but that would be the end of it. Currently there's a bit of a nasty clutch judder if I don't apply enough revs + find the exact wrong point of the slip point in the clutch pedal but it feels like it's slowly resolving as I drive it more. I would not recommend the competition clutch unless you really need the extra clamp force. I think this clutch combined with the Nismo operating cylinder is going to be exactly what I want. Enough bite that you need to remember the release point to avoid stalling or rough shifts, but progressive enough that it's not hard to drive by any means and not heavy at all. I tried a "super single" clutch on my friend's 997.2 Turbo 6MT and that was absolutely horrid. It runs an electrohydraulic power steering pump for the clutch power boost so there's zero feedback in the clutch pedal and there was a horrific clutch shudder well after break-in due to the lack of marcel springs or hub springs in the friction disk. It felt like the slip zone was the thickness of a single toe twitch as well so it was almost impossible to avoid stalling it unless you gave it a ton of revs and just dumped the clutch instead of trying to be smooth with it. I was terrified of pulling out in front of traffic. I have also tried some kind of "super single" on an EK9 and that makes this twin plate Coppermix look like a stock clutch. Releasing the clutch pedal even slightly too quickly feels like you're getting rear-ended. The pedal is extremely heavy as well and there's no vacuum assist like the GTR.
    • GTSBoy
      AC Compressor

      By GTSBoy · Posted

      Yeah, well I was probably way underguessing the $300 figure anyway. Just multiplied a "normal" by 4 for the purposes of pointing out it's not cheap, particularly if it has to be repeated.
    • joshuaho96
      AC Compressor

      By joshuaho96 · Posted

      We have an alignment shop out here that does what you're talking about but he wants like 800 AUD a pop. DIY is "cheaper" but once you start accounting for the value of your time I'm not sure it's worth it.
    • The Bogan
      Drag radials and rims, Sydney

      By The Bogan · Posted

      Sold
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      The main catch phrase for any car is "the eye of the beholder", and "personal tastes and preferences" And as for the plastic "flares", I honestly think they look cheap and tacky, and I cannot see them aging well, maybe if they were body colour they might look better to my eyes, but, I would still prefer it the were more like the older WRX STI models that had the wider body metal panels In saying all this 5hit, I wouldn't buy a new WRX again, even if it had the wide body metal panels    
×
×
  • Create New...