Jump to content
SAU Community

What power level are people getting from a gtx3582r on pump

lcxu105

By lcxu105,
in Engines & Forced Induction

 Share

Recommended Posts

lcxu105 Proficient

lcxu105

Posted
Posted

Just wanted to know  what power everyone is making from a gtx3582r on 30/25 engines see people making anywhere from 300 to 600 with gt35 turbos.

Most are running e85.

I want to know for pump 98.

And before you say check the dyno results I already have not much there for GTX 35

Kinkstaah Grand Master

Kinkstaah

Posted
Posted

If it's a 2.5 it'll be pretty nuggetty.

I have this turbo and on my 98 tune is about what WARLORD mentioned just now. 400kw at about ~23psi.
Mind you, its a RB28 and not a RB25/30. So like always your results will vary.

mr skidz Veteran

mr skidz

Posted
Posted
If it's a 2.5 it'll be pretty nuggetty.

I have this turbo and on my 98 tune is about what WARLORD mentioned just now. 400kw at about ~23psi.

Mind you, its a RB28 and not a RB25/30. So like always your results will vary.

400kw is good power, How's the response on your GTX3582 at 23psi decent?

Kinkstaah Grand Master

Kinkstaah

Posted
Posted

It was about 370 but through an auto, which makes it more responsive in terms of power to road speed that's for sure.
Also a RB28 which has had quite a lot of work.. so I don't think my setup is really that comparable to the OP. But for pure power, I suppose it is.


On a standard RB25 with a manual (IMO) with a 7k rev limit it's just not enough of a powerband. RB26 maybe cause they can rev to 8k. The extra 1000RPM of rev band makes the difference for me. RB30 probably just fine which is why you see it a lot.

However if I was going to that extreme I'd personally get a Borg Warner and love life. The GTX3582 is about as big as you can fit to a stock manifold which is kind of how mine ended up there low mounted, my engine bay is exceptionally boring.

  • Like 1
STR8E180 Proficient

STR8E180

Posted
Posted (edited)

i had this setup about 8 years ago before E85 and the GTX series turbos were around 

 

GT35 with .78 divided ( twinscoll ) T3 housing 

BP 89 octane 

drop in HKS cam shafts 264 intake 272 exhaust 

standard RB26 bottom end

 360kw @ 19psi

 

dyno2.jpg

dyno2.jpg

Edited by STR8E180

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...