Jump to content
SAU Community

Recommended Posts

Hey guy another thread about gear oil

Every post i read turned into everyone saying each other is wrong with what oil to put in.

So it doesn't go into gear when cold unless i fight it

And it rarely crunches gear.

So reading the post everyone says use the following:

-Vmx-80

-Syntrans (i can only find syntrax?)

-redline shockproof (blue??)

Can i get a definitive answer please?

Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/
Share on other sites

Redline shockproof is somewhat of a bandaid solution to a gearbox that has sufficiently unhealthy synchros that they pretty much don't work.  Not the best solution, but compared to a complete rebuild, sometimes the best one available.  I used it in my RB25DET box after the transplant when it would not select any gear at all with the engine running (with conventional oil).  Instantly better.  Has been in there for years now, even though it has a reputation for not being the best thing to run long term.

Other gearbox oils are just gearbox oils.  Some a bit better than others.  Some offer the same rescue service that shockproof offers.  If your box refuses to engage gears when cold, I suspect your first port of call would be to try the best conventional oil and see if it helps, then be prepared to try the smurfs' blood.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/#findComment-7768212
Share on other sites

3 hours ago, Jonnoo said:

Syntrax $30p/L
Vmx-80&vmx-m $38 p/4L

Is syntrax really worth the money extra

Seems a small investment. What do you think you have in your box now that is different from the cheaper oil? I think you'll find Redline Shockproof is not cheap either.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/#findComment-7768481
Share on other sites

It wasn't about cheeping out, it was more about noticeable differences between the 'common oils' before i went with the redline. :)

Anyway its all done, i used syntrans

easy job, hardest part was getting the filler plug off.

Drained i recon just over 1.5 ltrs
Filthy oil had a bit of sludge
No big chunks of metal on the magnet

Filled about 2.4-2.5 L
Hopefully shes all good! If not its redline time! :)57b931782409e_ImageUploadedBySAUCommunit

Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/#findComment-7768483
Share on other sites

The 2 bottles above is how much came out

I used those 2 plus half a third, but i also spilt some.
No idea where a liter would have disappeared to tho

Gear changes do feel smoother
No abnormal crunches (not that there ever was) but definitely smoother...
I wont know for sure until tomorrow morning.

I think the clutch is disengaging properly, it doesn't roll when on a flat surface, next job is to bleed the clutch, never know when it was last done.

Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/#findComment-7768493
Share on other sites

2 hours ago, Jonnoo said:

 


I used syntrans

 

I know. I recommended Syntrax or Motul Gear but never mind. Do you in fact have any clutch pedal free play?

Anyway you may be right about the box. An RB20 box won't stand too much caning.

Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/#findComment-7768966
Share on other sites

I know. I recommended Syntrax or Motul Gear but never mind. Do you in fact have any clutch pedal free play?

Anyway you may be right about the box. An RB20 box won't stand too much caning.

Unfortunately they only had 1L in stock! I did try for the syntrax though.

Not really free pay but if i rev the car the peddle goes soft i can feel it sort of go lower if my foots resting on it, if that makes sense?!?

Yeah behind the 25 i don't think itll have much left even if it was fine

Link to comment
https://www.sau.com.au/forums/topic/466379-rb20-gearbox/#findComment-7768970
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, all the crude is used for fuels and petrochem feedstocks (pesticides, many other chemicals, etc etc). But increasingly over the last few decades, much of the petrochem synthessis has started with methane because NG has been cheaper than oil, cleaner and easier and more consistent to work with, etc etc etc. So it's really had to say what the fraction either way is. Suffice to say - the direct fuels fraction is not insigificant. Heavy transport uses excruciatingly large amounts. Diesel is wasted in jet heaters in North American garages and workshops, thrown down drill holes in quarries, pissed all over the wall to provide electricity to certain outback communities, etc etc. Obviously road transport, and our pet project, recreational consumption camouflaged as road transport, is a smaller fraction of the total liquid HC consumption again. If you're talking aboust Aussie cars' contribution to the absolute total CO2 production of the country, then of course our share of the cubic mile of coal that is used for power generation, metallurgy, etc adds up to a big chunk. Then there is the consumption of timber. Did you know that the production of silicon metal, for example, is done in Australia by using hardwood? And f**king lots and lots and lots of hardwood at that. Until recently, it was f**king jarrah! There are many such sneaky contributors to CO2 production in industry and farming. NG is used in massive quantities in Australia, for power gen, for running huge water pumps (like, 1-2MW sized caterpillar V16 engines running flat out pumping water) for places like mine sites and minerals/metals refineries. And there are just a huge number of those sort of things going on quietly in the background. So NG use is a big fraction of total CO2 production here. I mean, shit, I personally design burners that are used in furnaces here in Oz that use multiple MW of gas all day every day. The largest such that I've done (not here in Oz) was rated to 150MW. One. Single. Gas burner. In a cement clinker kiln. There are thousands of such things out there in the world. There are double digits of them just here in Oz. (OK< just barely double digits now that a lot of them have shut - and they are all <100MW). But it's all the same to me. People in the car world (like this forum's users) would like to think that you only have to create an industrial capability to replace the fuel that they will be using in 10 years time, and imagine that everyone else will be driving EVs. And while the latter part of that is largely true, the liquid HC fuel industry as a whole is so much more massive than the bit used for cars, that there will be no commercial pressure to produce "renewable" "synthetic" fuels just for cars, when 100x that much would still be being burnt straight from the well. You have to replace it all, or you're not doing what is required. And then you get back to my massive numbers. People don't handle massive numbers at all well. Once you get past about 7 or 8 zeros, it becomes meaningless for most people.
    • @GTSBoy out of the cubic mile of crude oil we burn each year, I wonder how much of that is actually used for providing petrol and diesel.   From memory the figure for cars in Australia, is that they only add up to about 2 to 3% of our CO2 production. Which means something else here is burning a shit tonne of stuff to make CO2, and we're not really straight up burning oil everywhere, so our CO2 production is coming from elsewhere too.   Also we should totally just run thermal energy from deep in the ground. That way we can start to cool the inside of the planet and reverse global warming (PS, this last paragraph is a total piss take)
    • As somebody who works in the energy sector and lives in a subzero climate, i'm convinced EV's will never be the bulk of our transport.  EV battery and vehicle companies over here have been going bankrupt on a weekly basis the last year. 
    • With all the rust on those R32s, how can it even support all the extra weight requirements. Probably end up handling as well as a 1990s Ford Falcon Taxi.
    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
×
×
  • Create New...