Jump to content
SAU Community

How accurate is the 1010tires offset calc?

Adz2332

By Adz2332,
in Exterior & Interior Styling

 Share

Recommended Posts

Adz2332 Grand Master

Adz2332

Posted
Posted

Hey all

Has anyone used the 1010tires offset calc?

https://www.1010tires.com/Tools/Wheel-Offset-Calculator#

How accurate are they? 

Im currently trying to work out sizes for a set of rims for my torana. All the old guys use backspace this and backspace that. But im looking at a modern set of work emotion T7R -2P.

Ive test fit my RPF1s on the rear (pics below) they are 10.5 +15. so by using the above calc and my tape measure how accurate would it be? the T7Rs can be made to any offset to which helps and the largest 11.5 width with around a -20 offset could work... if the calc is right

 

cheers

1958431_10153976365785215_1573365432_n.jpg

1975081_10153976365510215_232702941_n.jpg

10150533_10153976364980215_899077824_n.jpg

Link to comment
Share on other sites
Hadouken Grand Master

Hadouken

Posted
Posted

Many people use the multitude of offset calculators online.

They are accurate in the sense that they are only doing simple maths with wheel offset and width calculations that you yourself can do to the same degree.

The accuracy of the matter comes when you have to measure guard clearances to see if you can accommodate the wheel. Then we talk caliper clearance, strut clearance, camber, full lock clearance blah blah blah

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stop on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, you need to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • alexburns
      Interior Light Problems

      By alexburns · Posted

      @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
    • Duncan
      GReddy Injector Help!

      By Duncan · Posted

      Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
×
×
  • Create New...