Jump to content
SAU Community

R32 GTR - Aftermarket Radiators and Factory Shorud

WantGTR

By WantGTR,
in Engines & Forced Induction

 Share

Recommended Posts

WantGTR Mentor

WantGTR

Posted
Posted
R32 GTR - Aftermarket Radiators and Factory Shorud

Hi All, 

 

Have been looking around and it seems some of those with aftermarket radiators have hacked up/no shrouds and others have them intact. Who here has a aftermarket rad with a factory shroud that fits?

HarrisRacing Proficient

HarrisRacing

Posted
Posted

Koyo radiator, factory fan and shroud. No touch. I also installed new radiator bushings and pulled them all the way forward on install. Worn bushings could have caused mine to hit. Another option would be to machine some offest bushings pulling the radiator further forward


GTSBoy Grand Master

GTSBoy

Posted
Posted
14 minutes ago, bcozican said:

sometimes that chopping etc of the shroud/ rad from the fan comes from worn / broken engine mounts when the car brakes etc the engine can move forward hence closing the gap / changing the alignment of everything... been there !

Engine mounts maybe.  In my case and at least a couple of others I've seen it's simply the radiator getting sucked back towards the engine by the engine fan.  It doesn't seem to happen with stock radiators, so maybe they are just too thin (to take up the room) and too thin (to put up enough resistance to airflow) to move far enough against the rad mounts.

 

I just jammed some more rubber into my upper mounts (on the back side) to pre-load them and prevent it moving back.....well, after it has already sliced a line through my shroud!

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

nope, don't like their welds :)

but they're massive up your way, Ryan Tuerck uses them... if you're bored... go compare the welds on a Plazmaman FMIC and a Mishimoto :)

CEF33Y Experienced

CEF33Y

Posted
Posted

I've got a cefiro, so not a gtr. But, 

 

I run a 52mm rad with the stock shroud and fan. Had a few drama's with the fan hitting the shroud.

I machined some new lower bushes out of nylon, and made new brackets for the top with no bush.

 

Haven't had a issue since. Car is used for drifting so gets a bit of a thrashing. Tried twin thermo's early on, and they were shit.

Granted, they weren't expensive ones, but stock fan and shroud is simple, and it works.

 

Oh and don't underestimate how much the stock fans flex, I had a Z32 fan (greater offset, but had one lying around) on after the thermo's shat themselves , had a decent 15mm gap fan to rad and it still grabbed the radiator at high rpm.

TXSquirrel Community Regular

TXSquirrel

Posted
Posted

What is the thickness of factory radiator?  Mishimoto is only 32mm so it should have fewer clearance issues, and 10% cheaper than Koyo here.  They also have great lifetime warranty that even covers collision.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted
1 hour ago, Dan_J said:

well i personally dont, but hey each to there own....

only if done right.. and 9/10 times it is done wrong...

Most owners just hard wire their fans OR use shitty fan controllers that turn off and on constantly like a strobe light.. followed by those who just hook it up to their OEM overheat fan relay/thermoswitch.

You need a proper fan controller either a standalone unit OR through your car's aftermarket ECU to set OFF and ON points followed by some form of hysteresis - only then would that be consider an appropriate installation.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


×
×
  • Create New...