Jump to content
SAU Community

Recommended Posts

Hello. I am in the finishing stages of a 3.2L gtr build and was settled on using g a G42-1450 but the more I read about the 9280, the more I'm starting to sway. It won't give me the same peak power but might make it a faster car due to better responce and torque while still netting a 4 digit dyno sheet. Im thinking 1.45 twin scroll rear housing. What do you guys think?

The power target would be helpful with this discussion

Generally speaking, most people I know who have tried the EFR9280 have not been particularly blown away so far, exhaust back pressure seems to be a thing - especially on bigger engines... if you're going to do it then the 1.45a/r hotside is the only option I'd consider.  The G42 1450 is definitely going to flow better but also most definitely comes at an impact to response, in fact one of the guys I know went to a G42 1200 from an EFR9280 and that delivers power in the higher rpm better but even that turbo added reasonable lag over the EFR.

 

  • Like 1
7 minutes ago, Lithium said:

The power target would be helpful with this discussion

Generally speaking, most people I know who have tried the EFR9280 have not been particularly blown away so far, exhaust back pressure seems to be a thing - especially on bigger engines... if you're going to do it then the 1.45a/r hotside is the only option I'd consider.  The G42 1450 is definitely going to flow better but also most definitely comes at an impact to response, in fact one of the guys I know went to a G42 1200 from an EFR9280 and that delivers power in the higher rpm better but even that turbo added reasonable lag over the EFR.

 

Interesting that everyone is saying back pressure is a thing  - I assume that is only once you starting pressing out 900+hp?

Here is my 8474 using 1.05A/R on 3.2L Nitto.  about 750hp at hubs.     eMAP/MAP is rarely over 1.2:1  as you can see here 1.17:1 @7515rpm     

Yes circuit car, not Drag car - but I guess I this would be around 800-820hp at the engine - at what point does exahsut pressure become a problem - ?   Or do you think I already have a problem...?

 

Screenshot 2021-04-16 124204.png

1 minute ago, R32 TT said:

Interesting that everyone is saying back pressure is a thing  - I assume that is only once you starting pressing out 900+hp?

Here is my 8474 using 1.05A/R on 3.2L Nitto.  about 750hp at hubs.     eMAP/MAP is rarely over 1.2:1  as you can see here 1.17:1 @7515rpm     

Yes circuit car, not Drag car - but I guess I this would be around 800-820hp at the engine - at what point does exahsut pressure become a problem - ?   Or do you think I already have a problem...?

 

Screenshot 2021-04-16 124204.png

Nice!  Awesome to finally see some data on the EFR8474 looks really solid in terms of what the data is saying about it - I'd be happy with that EMAP at that power.  What is odd though, and seems to be a bit of a trend...  where your IMAP is, and where your turbine speed is lines up with 90lb/min of compressor flow.   Do you reckon you're making the power you'd expect when your compressor speed and boost level suggest you are pushing at least 90lb/min of air?  This is part of what I've been told from people who have tried black series EFRs, they aren't getting the numbers they were expecting before they run out of compressor speed but perhaps the expectations need to be adjusted?

And yeah, the back pressure comment was about people looking at making use of the >100lb/min rated compressor flow of an EFR9280 - so closer to the 1000hp @ hubs territory, unfortunately I don't have first hand data so much as just going from people who I'm spoken to who have used them.  

  • Like 1

back pressure not relevant to compressor flow. (in the context of the operating point on a compressor map. yes, it affects VE)

but remember that 2.6 bar gauge inlet pressure will end up being more like 3.7 absolute PR (Possibly higher) once you factor in the inlet filter and intercooler pressure drops, which crosses closer to low 80s flow point at that wheel speed.

i'd be happy with 750hp at the hubs at this operating point. 900 at the hubs through diffs and gearbox flowing ~85lb/min is asking a bit much isn't it?

the Motec will have a logged VE calculated airflow. if your injector data is good and you lambda=target the Motec calculated airflow will be accurate if you wanted to verify.

Edited by burn4005
  • Like 1

Sorry what I meant was, in answer to this question - "Do you reckon you're making the power you'd expect when your compressor speed and boost level suggest you are pushing at least 90lb/min of air?"    -  I'd say 'I think so',  given the restriction to overall flow caused by eMAP.       

Would that be correct?  Or am I misunderstanding?

 

 

13 minutes ago, R32 TT said:

Or am I misunderstanding?

Probably misunderstanding. The compressor map should be viewed as a statement of fact. If the shaft speed is Z and the PR is Y, then the flow on the X axis that corresponds to that operating point is what the turbo is flowing. That flow is happening regardless of the restriction caused by the EMAP. If the EMAP were some different value and your turbo was operating at that same point, the flow would still be the same value. Make sense?

I think the element of surprise exhibited by other posters above is that the operating point you describe sounds like you shoudl be making more power than you think you are, which starts to throw some doubt on the factiness of the compressor map (or perhaps the measurements you have to put the operating point on the map).

  • Like 2

The trick is there seems to be a trend of this from the few black series EFRs I've seen results in, at least one tuner I've spoken to has decided it's a back pressure issue but this data doesn't suggest that to me.  The trick is I don't know where to go with it beyond the possibility that the compressor map or something about the data is not accurate which I'm not going to leap to concluding.

If you follow the compressor map the line where 116,000rpm sits hovers over 90lb/min until about PR3.2 which I would be surprised if it is reaching that high, but never know. 

Fwiw Gen2 GTX3582Rs fall fairly short of 90lb/min on the compressor maps and cars have made more power at the hubs than this on E85.  Not hating at all, I would prefer an 8474 over a GTX3582 but there are things I still have some question marks about

Yes all good - the only way for me to know is swap to a GTX3582 or 6466, perhaps 6870 to compare.  A fair bit of money just to experiment though,  and then - will I miss how it drives...?     that said the 8474 is noticeably lazy compared to the 8374 for just an inducer change.  Its not the "same down low but more up top" the internet seems to suggest.  

Edited by R32 TT

You know Elon Muskrat has won a contract with the Lebanese space agency to make a special Uranus probe lander mission using emotionaltron ECU and GTST body shell with special hiflow fitted with EFR black series internals using all the hypothesis off this forum, he was saying the key is the independent staged drive by wire and keeping the turbo on the small side cause when you do a hektik launch everyone knows that its area under the curve that is important when going to Uranus

  • Haha 1
On 4/16/2021 at 5:28 PM, R32 TT said:

Yes all good - the only way for me to know is swap to a GTX3582 or 6466, perhaps 6870 to compare.  A fair bit of money just to experiment though,  and then - will I miss how it drives...?     that said the 8474 is noticeably lazy compared to the 8374 for just an inducer change.  Its not the "same down low but more up top" the internet seems to suggest.  

Yes, yes... Come to the dark side

  • Like 1
  • Haha 2
15 hours ago, SimonR32 said:

Yes, yes... Come to the dark side

Run an OPR and an oil filter and they will last, at least they won't shit out turbine wheels if you accidentally over speed them :)

2 minutes ago, Dose Pipe Sutututu said:

Run an OPR and an oil filter and they will last, at least they won't shit out turbine wheels if you accidentally over speed them :)

Have been over speeding my 8374 by a few 1000 rpm since the day it was put on 2017. Was pulled off a few weeks ago in perfect condition. No shaft play, no missing turbine wheel. 🤷‍♂️

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
    • Yup but for me its the HR ! Cut my teeth on the old holden 6s in the day ! And here's me thinking in the day it was also the 300ZX and the Mitsubishi GT3000 ! All, as well had good lines, but always seemed to need finishing off, style wise.
×
×
  • Create New...