Jump to content
SAU Community

Recommended Posts

Garrett Dash 5 bb turbos bolt on for RB26 Y pipe dump pipes

Hi Guys Selling a Pair of Dash 5 bb turbos off my R33GTR ceramic coated turbine housing in very good condition going fine when removed, I brought these brand new from MTQ.Going to single turbo. Also ceramic coated ported stock exhaust manifolds. Stainless dump pipes separated waste gate type. Y pipe twin 3 inch feeding into single 3 inch. 1500 the lot or 1300 for turbos.

Please feel free to call with any questions. If i don't answer leave a message  ph 0411571454

IMG_1261.JPG

IMG_1262.JPG

IMG_1263.JPG

IMG_1264.JPG

Only about 15000 at the most I am a turbo specialist and I have inspected the turbine and compressor wheels and shaft play. Axial and radial play within spec.

On 22 September 2016 at 7:04 AM, stuz33 said:

Only about 15000 at the most I am a turbo specialist and I have inspected the turbine and compressor wheels and shaft play. Axial and radial play within spec.

Y pipe is sold

On 25 September 2016 at 3:08 PM, tayski said:

I'll take the lot if you can post to Melbourne 

Can post to Melbourne give me your details

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sell it and buy something newer? 😛
    • Better then PooPooG... or is it PeePeeG? 
    • The steering wheel on my 97 s3 gtr is a little bit worn out, so im on the hunt for something mint. I notice that this type of steering wheel is on several other nissan's of the era.  Does anyone know if their all identical, or are there slight differences? I feel like gtr tax applies to anyone selling one, but if it comes from any other car the price is much less, even though its the same design.  Chat gpt says the material for the gtr is slightly different and it says gtr on the wheel, but every pic ive seen it just says nissan. 
    • I might have to say it.
    • Ahh... it's an early RE5R01A box, that means the pinouts I gave are wrong (they were for the RE4R01A 4-speed box)... I'll have to dig around in my docs to see if I've got that schematic (they used the same gearbox plug, with the vacant pin wired to the direct drive clutch solenoid)...prolly hidden away in a supplement somewhere... ...there were 3 variants of the RE5R01A ~ this early schema was what we called the 'dumb' 5 speed ; it's what jatco called a 'medium duty' box, with torque holding up roughly ~200ft/lbs or so, which was good for NA from RB20/25DE and up to around VG30 output spec. With the RB25DET (and VG33/35 mills), the only options they had was the 4-speed 4AX00 box, which had been beefed up to handle the extra torque (primarily for the VG35, but it also suited the RB25DET mill and others)...and the RE4R03 box in large 4WDs a lot of the time... ...the next variant of 5-speed was redesigned, stronger, and 'smart'...first ones had external TCU with internal (on valvebody) Shift Control Unit, pressure switches, and 2 x TSS...and the last ones had internal TCU+SCU setup, with CANbus control etc etc. @DRoc81 On the RHS of the box towards the rear, there should be a stamped silver ID tag -- what's the model number? Oh...and with the early 5-speeds, the torque converter control solenoid assembly should be replaced as well (31940-60X00)...it's a bit Murphy's Law ....if one has failed, bet on the rest not being far behind ...
×
×
  • Create New...