Jump to content
SAU Community

Recommended Posts

1 hour ago, BakemonoRicer said:

Are you aware the CD009 will become the lowest point on the car? They hang a LOT lower than the chassis rails, just an FYI. 

What you need is a Samsonas....... 

lol... fuark the peer pressure is real, also my car isn't that low (as you can see in the photos).

 

38 minutes ago, BakemonoRicer said:

Paintjob looks mad.... did you take the strut towers off to do a rust repair while engine out?

 

E.g. 

http://blog.garage-yoshida.net/wp-content/uploads/2021/02/IMG_0100.jpg

http://blog.garage-yoshida.net/wp-content/uploads/2021/02/IMG_0099.jpg

We sanded the towered back to bare metal around the rust areas, wasn't as bad as those photos. Hit is mum with rust converter and re-sealed, then painted over.

For real, I am currently shopping for a very expensive gearbox while my clutch is out. (???? cars...)

Buy once, cry once, then enjoy the benefit.

That said is there actually any benefit with a Samsonas for your intended use 😛

1 hour ago, Kinkstaah said:

That said is there actually any benefit with a Samsonas for your intended use 😛

Can grab another gear mid drift at Powercruise and look like a sik karnt :D

But no.. I will not Samsonas my car.

  • Like 1
35 minutes ago, Dose Pipe Sutututu said:

Can grab another gear mid drift at Powercruise and look like a sik karnt :D

But no.. I will not Samsonas my car.

But how can this should work at all ? . . . . . 

Easy samosa recipes to cook at home during lockdown

2 hours ago, dr phil said:

Somebody please do a BMW DCT conversion. There is a GTR kit now for the transfer case too.

I looked into this for the LS! It looks like there's an adaptor plate for the LS, and the gearbox itself....

... and nothing else. No easy to find dimensions/sizes of things, no electronics, 
Noone sells the rest of the 'kit' to make it actually 'work'.

But I wish they did >.>

18 hours ago, dr phil said:

Somebody please do a BMW DCT conversion. There is a GTR kit now for the transfer case too.

I'm looking at this for the Silvia using HGTs stand alone. It "appears" on paper to not be that much more than CD009 conversion, but obviously with a little more work/complexity. 

As my car will only be a little 4cyl, I am hoping I can get away with the ZF8HP70 or 75. 

Flappy paddle last minute corner entry/exit changes would be pretty hektik though... 

  • Like 1
23 minutes ago, ActionDan said:

Flappy paddle last minute corner entry/exit changes would be pretty hektik though... 

Very sex, this is why you see M2/3/4s at Wakefield just fly out of the fish hook, all the manual boys trying to rev match, shift dis dat, they're just cycling through the gears and flying out.

 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hello everyone, I am from Malta and have recently bought myself a fully stock 1992 Nissan Skyline GTS. It has the RB20DE engine and thus is NA. Unfortunately, not a lot of information can be found online related to the GTS, unlike the information for GTS-T and GTR variants. Apart of the Skyline, I also got a 1984 Porsche 924 2.0l NA and a 2002 Renault Clio 1.5DCi for everyday use. Excited to be apart of the community and perhaps get better information on cars such as the GTS.
    • The fuel pump bracket just slides straight up.  Below is a pic I stole off a site. But basically put hand in for fuel pump, wiggle it all about a bit while pulling up. 
    • Went digging Duncan, there's another "item" that sits down under the plenum that the second pipe from the IACV goes down to. I believe that's the one that is apart of the cold start portion, and it then comes back up under the middle of the factory top plenum. I believe you will find it is unneeded on the forward facing plenum on Cheryl.   I just went digging further for some pics on the location of the one way check valve, and found something that confirms my thoughts from the first half of this point. I feel you can just block off that port that is coming down.     I can also confirm, the other line that you were thinking for vacuum that will just need a one way valve put into Cheryl is 100% correct too. The one way valve is normally screwed into the back of the factory inlet plenum.
    • You’re an absolute legend man. Cheers.  
    • The rule of thumb for any GTR thats doing a single turbo conversion is..... seqy... and when i say seqy, i dont mean the pos PPG either. *flamesuit on*
×
×
  • Create New...