Jump to content
SAU Community

Recommended Posts

1 hour ago, GTSBoy said:

......By contrast, Sydney had it so good with water that original fell on pristine mountainsides that their water supply engineers never learnt how to scrub water properly and so for years and years there were Giardia outbreaks and the like, that only stopped when some E&WS engineers went across and taught them how to do it.....

our Wombats and Kangaroos wee in that river.

  • Haha 4

So I decided that I wasn't happy with how I originally wrapped the loom with fleece tape. I didn't factor in the new intake manifold/plenum so it always sat a bit funny.

Yep, I decided to unwrap it and redo how the wires would branch out. Added in a light twist too, here's hoping I didn't snap any 30 year old wiring because FML if I did.

PXL_20240726_063235339.thumb.jpg.8084f7fc864a17b8f20e62b21d770978.jpg

Took a few more photos of the shit box too, needed it for Enthusiast Insurance as they wanted photos to justify why my agreed value was above market by a fair amount.

PXL_20240726_063313986.thumb.jpg.c4bb286a8d69f20dbb121e064d972121.jpg

PXL_20240726_063016998.thumb.jpg.996df36e205ffd88e2baa50b6564cde8.jpg

  • Like 7
  • 2 weeks later...

Somehow I managed to snap off the coolant sensor wiring when I pulled through the loom, then at the same time managed to also snap off the coolant dash sensor plug too.

To make things even more fun, I thought it would be nice to recrimp the ring terminals for the earths, to only find out the terminals I had at home were too small for a M6 bolt to go through. 

Anyhow, managed to fixed the lot yesterday during lunch, installed the e-throttle. Slow and steady, but we are getting there.

Next is to tidy up the harness with some trusty race zip ties and then install the starter.

PXL_20240809_065753363.thumb.jpg.861cc4fec5329d168fe402b870c4357d.jpg

  • Like 8

Pissed off the random Raceworks fitting on my car, was fitting when the new motor went on. 

Not sure what happened to the original Speedflow one before the motor went bang.

PXL_20240817_050024925.thumb.jpg.d58e8f0f01ec8f8c93e76a89da7c667b.jpg

 

Doesn't look like the catch can fittings are going to be very fun with the throttle body (and pipe).
Are they on different planes?

2 hours ago, Dose Pipe Sutututu said:

@Kinkstaah

And yes, the exhaust is so quiet you just hear plenty of injector noise and solid lifter noise.

Oh you sweet summer child. This is a quiet engine bay and a booming exhaust where I'm from lol. Sometimes I do miss the RB.

  • 1 month later...

Not much car shit happening as of late, been so busy with work and decided to also study to do a massive career backflip.

So yeah, working 2 jobs, means no time for Dose Pipe plays with toys time.

Anyhow, new Philips XL Air Fryer came today. Went for the non Wi-Fi version which is like $50 cheaper.

New air fryer, who dis?

PXL_20241013_095612088.thumb.jpg.437bc57ac4ef2dbb9bc59d03d99a10e2.jpg

  • Like 1
  • Haha 1
8 minutes ago, MBS206 said:

What're you studying to backflip yourself towards?

Finished studying already, mortgage broking 😊

Started working already too, have settled a handful of refinances and learning the ropes. All have been simple PAYG clients (all family and friends, can't thank them enough, trusting me with their finances).

Will say goodbye to the IT world for good one day, nearly 2 decades of ups and mainly downs lol... I'm burnt out from corporate, constant moving targets, constant scope creep, never a fking clear definition of an end goal.

Hope I've made the right move, if not, I hear job seeker allowances aren't too bad LOL.

  • Like 4

Do conveyancing, I cannot be arsed trying to actually buy a house and do all the legal stuff you need to do to purchase myself

I pay cash now, you make happen.....

  • Like 1

Might be an option when the business grows, never too late to teach an old dog new tricks.

Mid life crisis dis dat, also means moving forward I won't be too inclined to buying our future house anywhere near the CBD or Metro Sydney.

Come at me man shed and hoist and motion racing SIM and maybe a dyno? Lol.

Dyno Tune your Car and Home Loan.

  • Like 2
On 13/10/2024 at 9:42 PM, Dose Pipe Sutututu said:

Not much car shit happening as of late, been so busy with work and decided to also study to do a massive career backflip.

So yeah, working 2 jobs, means no time for Dose Pipe plays with toys time.

Anyhow, new Philips XL Air Fryer came today. Went for the non Wi-Fi version which is like $50 cheaper.

New air fryer, who dis?

PXL_20241013_095612088.thumb.jpg.437bc57ac4ef2dbb9bc59d03d99a10e2.jpg

wait till you discover scented fabric softener, EVERYTHING SMELLS LIKE VANILLA NOW

  • Haha 1
On 10/13/2024 at 8:54 PM, Dose Pipe Sutututu said:

Finished studying already, mortgage broking 😊

Started working already too, have settled a handful of refinances and learning the ropes. All have been simple PAYG clients (all family and friends, can't thank them enough, trusting me with their finances).

Will say goodbye to the IT world for good one day, nearly 2 decades of ups and mainly downs lol... I'm burnt out from corporate, constant moving targets, constant scope creep, never a fking clear definition of an end goal.

Hope I've made the right move, if not, I hear job seeker allowances aren't too bad LOL.

What's your best deal to refinance my mortgage? 😛

I just want to be paying the banks the least in interest, so no fees, low interest, and either redraw available or 100% offset accounts...

24 minutes ago, MBS206 said:

What's your best deal to refinance my mortgage? 😛

I just want to be paying the banks the least in interest, so no fees, low interest, and either redraw available or 100% offset accounts...

Depends on your LVR and also loan size :)

Happy to help out, flick me a PM with an email or mobile

3 hours ago, Mohsen said:

do you want to occasionally come back to the IT world and do CSVs for me? i pay

CSV? Come on lad, I'm all about PowerBI these days.

I would consider working as a PowerBI or ZOHO DataPrep consultant, but nah, I've had enough of IT. Two decades of being in somewhat in an industry I kind of just chose because I had zero guidance when I was younger.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...