Jump to content
SAU Community

Recommended Posts

Road tuning, I need a mentor

Hello, finally got my rb30 running. It was definatly worth it. Boost comes on earlier etc. still thinking about running 8cm rear housing cause there's not enough tourque for me. It's got plenty of power don't get me wrong. Ive got a feeling it has to do with timing comming on to boost .I'm currently road tuning. Found a copilot so I don't have to think to much. 

Link to comment
https://www.sau.com.au/forums/topic/468382-road-tuning-i-need-a-mentor/
Share on other sites

I changed it last night. Took it for a drive to day. It's everything I've been wanting and more. It spikes to 20psi then dies down to 15.  it spins the wheels in 1 2 3. 

I'm so much happier with every charictoristic. It's got 5 psi at 3000

I was never looking for over 300kw just tourque.

i hated the 25 with 10cm. The 30 with 10 cm was ok. But with the 8cm it's like a v8

im going to sell it now and get my dream car. An r32 gtr completely stock with a 3.4l

It wouldn't be stock then would it lol. Hope you have deep pockets my friend with the cost of a 3.4L and R32 gtr's at the moment.

On topic, road tuning is not easy and is a time consuming process to fine tune maps. I hope you have the right equipment at your availability so you don't do damage.

Yes. I agree, with everything u say, especially the tuning. I'm scared my afrs are lean on boost transition especially when I'm not full throttle. Full throttle is 11.7 but leading up to that seems a lot lighter if I'm moderating the throttle. That's somthing I'll address in the next drive to keep it safe. I'm keen to get some ears on to listen to knock aswell before the next drive. If there's one thing I know it's I have no idea what I'm doing..

as for the over oiling thing I think I've got that covered. After a total of 3 hours of reving to the limiter I've collected 200mm of oil in my catch can. Easily eliminated by running a t piece to the turbo drain.

Better to put more fuel in and take it out later to be safe than lean out and destroy a motor. What sort of ecu do you have? Knock ears and equipment isn't cheap just as a FYI. Also what sort of wideband are you running?

Plenty of variables to consider, if you are really keen I'd suggest getting stuck into tuning forums and doing plenty of research to further your knowledge on tuning. Tuning a full throttle run is quite easy to do and takes minimal effort but getting a perfect map for different load points will take time and patience.

As a side note, 200ml (if that is correct) is a massive amount of oil to have collected in the catch can even if you are bashing limiter for 3 hours (not sure why you need to be revving to the limiter constantly either).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Certainly. It is probably broken under the wire style clamp. At least that one is easier to get at than the front one.   Sounds like it isn't a major leak, I'd start with backing off the the water feed and return banjos into the turbos half a turn then tightening properly. Hardlines can still crack over time, either in the tube (particularly when turbos are changed if the banjo is siezed in the the tube) or at the brazed joins between the lines and the banjo fittings. A coolant system pressure test will reveal all. BTW you'd be able to get a sump without exchange, it will just cost more as they will have to source another stock one for the next customer. If you want to address the sump a much better option is something like this https://www.hioctanedirect.com/hi-octane-racing-sump-extension-nissan-rb26 that you weld in locally (and add the oil return fittings at the same time)
    • Pretty sure you are thinking of the throwout bearing there (which you should change when you change your clutch), when they are worn they will get quieter if you put your foot on the clutch. An input shaft bearing is turning/noisy at all times.
    • I’ll have more of a look into Recaros over the weekend. It’s taken me 2 days to figure out which Bride seats suit my application haha.
    • I am aware of their presence, but the product page looked like that conversion will eliminate the AWD capability. Fact remains it's kind of a hassle to send my oil sump halfway around the world and buying an extra one is expensive and unnecessary. Before I go hat route I'd explore more local options.    Would you recommend I just pull the engine and renew as many things as possible since I'm already having problems with some leaks? Would have to get an engine crane first though.
    • Are there any indicators that the vehicle is in limp mode?  Any dash light, or something.  Or is it just lack of acceleration?
×
×
  • Create New...