Jump to content
SAU Community

Recommended Posts

Hi,

I need someone in QLD who can tune this ECU, Gavin Woods can't, Sub-Zero can't, all the HKS dealers can't.... I rang up BD4's in Sydney which is a HKS ProDealer and they reckon they are the only ones in Australia who can tune this ECU. If anyone knows of workshops in QLD who can do it let it be know :)

Otherwise I will be going on a little roadtrip ;)

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/
Share on other sites

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

be careful with the HKS Fcon V ecu's. Not many around australia know how to tune them because most the time the language is in Japanese and u need HKS accreditation to recieve access to the software. Only time i've heard of ANYONE in australia tune one was when Susumu Koyama from Jun Auto in japan went over to perth to tune a few cars (inclusive of a sexy looking grey R34 GTR)

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-950906
Share on other sites

I just spoke to Jim @ Croydon Racing Developments (CRD) and he is trying to source the HKS F-Con S/V laptop software from HKS at a cost of $4000 so he can tune this excellent ECU...

Just remember that actual costs always run nearly double what he quotes you. Keep that in mind and you'll be fine.

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-950907
Share on other sites

;) um, you could pay twice the money to get something like that tuned..

or throw it out and go for one of the common ones that can be tuned by anybody. Its a waste in a way, but unless you can find a good tuner for it, what is the point?

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951015
Share on other sites

Ok the deal with HKS computers as far as i know is:

FconV

Does fuel only. Now the bad thing with this piggyback ecu is that the standard ecu will still retard timing and add/remove fuel 7.5% either way of the tune put simply. I like to think of it as HKS's answer to the SAFC. Who would pay someone big money to tune an FconV or FconS when you could get an safc done for 200.

FconV Pro

Does fuel and timing and shitloads of other stuff, comparable to a motec, but still not as comprehensive. With thi ecu you have to buy an air temp sensor and a MAP sensor to make it work, an additional $1000 ontop of the ECU. Also it is still a piggyback, leaving the standard ecu to do aircon and demister etc. the fuel/timing is eliminated with a special harness which isnt cheap too. Tuning was very expensive last time i got a quote, it put me off getting one of these ECU's. Imagine forking out truckloads of money everytime you do a mod just to tune your car to it.

-rb25

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951147
Share on other sites

Serious question, and not a go at you or anything....

If its a step below the PFC, and you have to drive from the sunny coast to sydney for tuning ... Why use it instead of the PFC?

If there are some magical features ross hasnt pointed out yet (although I guess MAP is an advantage over MAF) I'd be interested in hearing them. Always open to new ideas and suggestions for ECUs :rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951859
Share on other sites

rb25 the HKS FCON V is worlds apart from the Apex SAFC, maybe one step behind the Power FC, for reference I have the Pro Version and BD4's do have the Pro Software.

for sure, it is more comprehensive than an safc, but at the end of the day, it does fuel maps, not timing, and imho thats ordinary anyway. powerfc is the go.

-rb25

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951880
Share on other sites

In Perth a guy is flown in over from Japan and all cars a done in one hit, it isnt just about having the gear and software it is all about knowing how to tune the software.

One shop here blew two motors and they hadent started to look into tuning, ripped it out and put in a Micro Tech (RX7).

Power FC is the way or something that a good local tuning shop can work on.

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951891
Share on other sites

Serious question, and not a go at you or anything....

 

If its a step below the PFC, and you have to drive from the sunny coast to sydney for tuning ... Why use it instead of the PFC?  

Because it is the pro version, which is proven a better ecu over the apex power fc.

The pro version is pretty much a MoTeC but uses a piggyback system.

And yes RB25 I have the harnesses and what not.

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951947
Share on other sites

i believe what Krawler is trying to say is ---> Why is it so much better than the Power FC? therefore making the drive to sydney worth it. Why couldnt u sell it buy a power FC and have it tuned here and save yaself alot of trouble

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-951985
Share on other sites

you can now get a newer PFC's will do MAP as well..

i think everybody is pretty much along the same lines though.. $1200 on a PFC, or lots of ****ing around and maybe headaches with the HKS. The HKS may in fact be a better ECU, and I have seen quite a few hypo GTR's with them in japan - and some 9second GTR have had them.. but if you can't get it tuned, or tuned properly more importantly its all a little irrelevent

Link to comment
https://www.sau.com.au/forums/topic/46850-tuning-hks-fcon-v/#findComment-952358
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What could be causing my clutch problem besides a bad master or slave then? Both those parts are new 
    • Just came across this, but in QLD I start leave again in 2 weeks, if it is still available I might drive up and check it out Unless, @MBS206 do you live near here????, if so I could hit you up with a finders fee https://www.gumtree.com.au/s-ad/hope-island/auto-body-parts/nc-mx5-factory-hard-top/1328976391
    • My hold point for future mods is that I want a OEM detachable hard top first, but, finding one is a pain, MX5 Mania are looking for one for me, but, as hens teeth are more common, finding one in Australia is proving problematic  I can get a OEM one from overseas, hell, you can still get new ones in 'Merica, but, shipping is a absolute killer and I cannot justify the cost, or the risk of it being damaged during transport As for the aftermarket hardtops, whilst they do the job of being a hard top, and are fine for a track car, they don't seal well (read: leak like a sieve in the rain), and you need a plastic/poly rear window, plus they are a bolt in option only and not made to be easily removed I liked how the hard top on my NB could be fitted, and removed, by myself, in less than 5 minutes I know it sounds bad, but I'm waiting for someone to write off a car with one so I can swoop in on their pain, it will go to a good home though, so my guilt of this is tempered
    • I’ve got one on mine and it’s fine, 
    • No, you don't want to plug the vacuum line, as that will turn that side of the booster into an air spring and probably make it feel worse. I'm not saying that the GTR master itself doesn't need a booster. I haven't paid attention to the GTR one to know what size it is cf the non-GTR ones. But when you think about it - they have to do the same job, which is to move a little slave piston a few mm to do what it is supposed to do, and that final action is the same on all the cars. So, it is very unlikely that the GTR MC is any different than the others, because it has the same pedal stroke and the same output requirement. The booster just makes it feel easier. I'd suggest you probably have an actual hydraulic problem. It's totally common on these old shitboxes.
×
×
  • Create New...